CLASS 1 LED PRODUCT
Eye Safety Warnings
Avoid staring/facing directly into the projector beam at all times. Keep your back to the beam as much as possible.
A stick or laser pointer is recommended to avoid the need for the user to enter the beam.
When projector is used in a classroom, adequately supervise students when they are asked to point out something on the screen.
In order to minimize power, use room blinds to reduce ambient light levels.
A.2.9.31 Gloss of housing of peripheral devices (15th / 22 meeting AG1 EK1):
The requirements for the gloss of housing apply to peripheral devices used at the visual display workplace according to BildscharbV. Peripheral devices intended for use outside the visual display workplace can receive a GS-Mark if the scope is indicated in the User’s Manual as well as the certificate.
That means the following wording is possible in situations where the use within the field of view is not intended and where sufficient hints are given in the User’s Manual for the avoidance of such situations to ensure that display work is not affected.
Wording in the certificate: “This device is not intended for use in the direct field of view at visual display workplaces. To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct field of view.”
1.Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over heating, it is recommended to install the projector in a location that does not block ventilation. As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air flow.
2.Do not use the projector near water or moisture. To reduce the risk of fire and/ or electric shock, do not expose the projector to rain or moisture.
3.Do not install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers that emits heat.
4.Do not use the projector in direct sunlight.
5.Do not use near any appliance generating a strong magnetic field.
6.Do not use the projector in areas susceptible to excessive dust and dirt.
7.Turn off the product before cleaning.
8.Turn off the product before removing the battery.
9.Disconnect the battery if the product is not being used for a long period of time.
10.Ensure that the ambient room temperature is within 5- 35°C.
11.Relative Humidity is 5 - 35°C, 80% (Max.), non-condensing.
12.Do not expose the battery to temperatures above +60°C (+140°F)
13.New or idle batteries can have short- term reduced capacity. Fully charge the battery before initial use.
14.Do not put the battery into your mouth.
15.Do not let the battery contacts touch another metal object.
16.Do not drop, throw or try to bend your product.
17.May explode if disposed of in fire.
18.Clean only with dry cloth.
19.Only use attachments/accessories specified by the manufacturer.
20.Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be (but not limited to):
▀■Unit has been dropped.
▀■Charger or plug has been damaged. ▀■Liquid has been spilled on to the
projector.
▀■Projector has been exposed to rain or moisture.
▀■Something has fallen in the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please contact your local reseller or service center before you send the unit for repair.
21.Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in fire or electric shock.
22.See projector enclosure for safety related markings.
23.The unit should only be repaired by appropriate service personnel.
24.Do not touch the projector for a long time while the projector is used.
25.CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type.
26.Dispose of Used Batteries According to the Instructions.
This appendix lists the general notices of your Projector.
FCC notice
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications.
However, there is no guarantee that inter- ference will not occur in a particular instal- lation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the device and receiver.
•Connect the device into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
Caution
Changes or modifications not expressly approved by the manufac- turer could void the user’s authority, which is granted by the Federal Communications Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interfer- ence received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque à l’intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
•EMC Directive 2004/108/EC (including amendments)
•Low Voltage Directive 2006/95/EC
•R & TTE Directive 1999/5/EC (if product has
RF function)
quipment
(Applicable throughout the European Union and other European countries with separate collection programs)
This symbol found on your product or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve natural resources.
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
