InFocus SP-LAMP-084 instruction

Lamp Module Replacement Instructions: SP-LAMP-084

NOTES:

Always use the InFocus lamp module designed for your projector model. Using the wrong lamp module may cause premature lamp failure and possible damage to the projector.

SP-LAMP-084 – Used in IN134UST, IN136UST

You can order new lamps from www.infocus.com (in select areas), your retailer or your dealer. Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty. InFocus is not liable for the performance, safety or certification of any other lamps.

WARNINGS:

•The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.

•To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.

•Unplug the power cord before replacing the lamp.

•Do not drop the lamp module. The glass may shatter and cause injury.

•Do not touch the glass surface of the lamp module. Fingerprints can obscure projection sharpness and may cause the glass to shatter.

•Be extremely careful when removing the lamp module. In the unlikely event that the lamp ruptures, small glass fragments may be generated. The lamp module is designed to contain most of these fragments, but use caution when removing it.

•Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement.

•When replacing the lamp while the projector is ceiling-mounted, wear protective eyewear to prevent eye injury.

•Hg-Lamp contains mercury. Manage with accordance with local disposal laws. See www.lamprecycle.org

1. Turn off the projector and unplug the power cord.

2. Wait 30 minutes to allow the projector and lamp to cool thoroughly.

3. Remove the screw on the lamp door.

4. Remove the lamp door.

5. Loosen the two captive screws that attach the lamp housing to the projector.

NOTE: If the projector is installed on a ceiling mount, be careful not to drop the lamp module once the captive screws are loosened.

6. Using the handle, carefully lift the lamp straight up, off of the alignment pins; being careful not to pinch the lamp connector. Dispose of the lamp in an environmentally proper manner.

7.Install the new lamp module, aligning the pins properly. Be careful not to pinch the lamp connector.

8. Tighten the screws. (NOTE: If the pins have not been aligned properly, the screws will not tighten securely.)

9. Replace the lamp door by putting the lamp door down (the hinges should be aligned) and sliding it back into place.

10. Replace the lamp door screw and tighten securely.

11. Plug in the power cord and press the Power button to turn the projector back on.

SP-LAMP-084 specifications

The InFocus SP-LAMP-084 is a high-quality replacement lamp designed specifically for InFocus projectors, ensuring optimal performance and longevity. This lamp is an essential component for users who rely on projecting vivid images and presentations in various settings, from classrooms to corporate environments.

One of the main features of the SP-LAMP-084 is its impressive brightness output. With a lumens rating that allows for clear visibility in both dimly lit and brightly lit rooms, this lamp provides an exceptional viewing experience. Users can expect vibrant colors and sharp details that enhance the quality of presentations, making them more engaging for audiences.

The technology behind the SP-LAMP-084 involves a high-pressure mercury bulb, which is known for its ability to produce high levels of brightness while maintaining good color accuracy. This technology contributes to the long lamp life that is achievable with the SP-LAMP-084, often reaching up to 5,000 hours in Eco mode. This extended lifespan reduces the frequency of replacements, making it a cost-effective choice for users.

Compatibility is another critical characteristic of the SP-LAMP-084. This lamp is designed to meet the specifications of various InFocus projector models, ensuring seamless integration. The straightforward installation process allows users to replace the lamp without needing specialized tools or extensive technical expertise, enabling a quick return to regular projector use.

Additionally, the SP-LAMP-084 incorporates advanced thermal management features. With effective cooling mechanisms, it prevents overheating, which can significantly extend the life of the lamp and maintain consistent performance. This attribute is particularly beneficial in demanding environments where projectors are used continuously.

Furthermore, the SP-LAMP-084 provides a reliable and consistent performance, backed by robust engineering and quality control processes. Users can trust that they are investing in a product that delivers both durability and efficiency.

In summary, the InFocus SP-LAMP-084 is a top choice for those seeking a reliable replacement lamp for their projectors. With its brightness, long lifespan, compatibility, and thermal management technologies, it stands out as a leader in projector lamp solutions, ensuring that users can deliver impactful presentations and experiences time after time.