IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE INSTALLING EQUIPMENT
This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of.
1.Read instructions - All the safety and operating instructions should be read before the product is operated.
2.Retain instructions - The safety and operating instructions should be retained for future reference.
3.Heed warnings - All warnings on the product and in the operating instructions should be adhered to.
4.Follow instructions - All installation instructions should be followed.
5.Use only the parts provided with the mount, along with any parts (commercially available) that are specified in this manual.
6.Do not modify the mount or the parts provided with the mount.
7.Do not use damaged parts. if any parts become damaged, contact your dealer.
8.All bolts and screws must be tightened securely.
9.Make sure not to block any ventilation openings when installing the projector.
10.Special techniques and experience are required when installing the projector with this mount. Contact your dealer to install the projector for you.
11.Once the projector is installed, safety checks should be conducted on a regular basis.
MOUNT10
PROJECTOR MOUNT
INSTALLATION INSTRUCTIONS
Step 1
Base Plate Connectors #1 and Projector Mount Ceiling Plate 1 with ceiling mounting holes #2.
Figure 1 |
|
|
|
|
|
1 |
|
|
|
|
|
| 4 | Ceiling Wire | 4 |
| 14" |
|
| Access |
|
|
|
2 | 3 |
|
| 3 | 2 |
|
|
|
| ||
|
|
| 2 |
|
|
|
| 8 5/8" |
|
|
|
Plate 1 |
|
|
|
|
|
Base Plate Connectors #1
Projector Mount Ceiling Plate 1
Insert Base Plate connectors #1 into the lateral positioning slots
#3 as shown in #4 from the underside of Plate 1. The lateral positioning slots will give you 4 1/2" inches of lateral adjustment for projector alignment.
Warning
The ceiling should be capable of supporting a weight
of at least five (5) times the projector(s) weight. If it cannot, the ceiling must be reinforced. Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury.
Hardware List
1. | Four (4) | 3/8 (inch) nuts | 7. |
| Eight (8) 6 (mm) flat washers |
2. | Four (4) | 3/8 (inch) flat washers | 8. |
| One (1) Ceiling Mount #1 |
3. | Two (2) | 8 (mm) screws | 9. | Two (2) Base Plate Connectors | |
4. | Fourteen (14) 6 (mm) screws | 10. | One (1) Horizontal Tilt Plate #2 | ||
5. | Eight (8) 6 (mm) rubber washers | 11. One (1) Horizontal Tilt Plate #3 | |||
6. | Two (2) | 8 (mm) rubber washers | 12. | One (1) Projector Plate #4 | |
Adjustment Ranges and Load Allowances
Horizontal Tilt (yaw) | +/- | 4 degrees |
Vertical Tilt (tilt) | +/- | 8 degrees |
Rotation | +/- 15 degrees | |
Lateral Shift | +/- 41/2 inches | |
Maximum Load Allowance |
| 450 Lbs. |
Step 2
Horizontal Adjustment Plate 2 (Base Plate Connector
Holes #3).
Figure 2 |
|
3 | 3 |
Wire | 10 5/8" |
Access |
|
3 | 3 |
7 5/8" |
|
Plate 2 |
|
Base plate connector holes #3 provide 15 degrees of horizontal adjustment.
Attach horizontal adjustment Plate 2 to projector mount ceiling Plate 1 using the four (4) 3/8" (inch) nuts and washers provided.