JVC GD-19L1G, GD-17L1G manual Troubleshooting

Page 21

Troubleshooting

Solutions to common problems related to your monitor are described here. If none of the solutions presented here solove the problem, unplug the monitor and consult a JVC-authorised dealer or service centre for assistance.

A.My monitor doesn’t work.

„Check that the power cord is securely plugged into the monitor.

„Check that the monitor is turned on.

„Turn the monitor off and pull the plug out, then put the plug in again and turn the monitor on.

B.My monitor shows no colors, wrong color, or dark pictures.

„Check the LUMINANCE, PICTURE ADJ. and COLOR TEMP. settings. See page 14 and15.

„In the PC mode, check the CONTRAST setting. See “LUMINANCE menu” on page 14.

C.The message "NO SYNC" appears .

This message appears when there is no video signal. After few seconds, the monitor goes into the reduced power mode.

„Check the connection.

„Select the required video signal input.

„Connect the video signal cable firmly.

„Check that your graphic card outputs the analog RGB signal.

D. The message “out of range!” appears on my monitor.

This message appears when the input signal is beyond the monitor capability.

Set your PC to a supported video mode; recommended mode is 1280 x 1024 at 60Hz.

E.The image is very unstable in the PC mode.

„Set your PC to a supported video mode; recommended mode is 1280 x 1024 at 60Hz.

„Restore the original factory settings by “Reset”. See “Reset menu” on page 16.

„Do the “AUTO ADJUST”. See “AUTO ADJUST” on page 17.

F.When connecting to the PC, installation of the device is required. See "Connecting the monitor to the PC" on page 11.

Note: Even if your PC’s setting is out of the range of video modes that are supported by your LCD monitor, it may still be displayed with reduced quality. This provides you with an opportunity to change your PC’s setting to a correct one.

The following are not malfunctions:

‧The monitor emits a strange sound when the room temperature changes suddenly. This is only a problem if an abnormality appears on the screen as well.

‧When a still image has been displayed for a long period, a faint residual image may remain on the screen for a short time after the power has been turned off or when another image is displayed. The image will eventually disappear.

‧When you see the monitor from the side, the color or brightness look different.

‧The LCD panel is made with high-precision technology and has more than 99.99% effective pixels. Fewer than 0.01% of pixels may be chipped or always lit.

ENGLISH

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents English For Customer UseContents Safety Precautions How to replace the fuse Power cordInformation for Users on Disposal of Old Equipment European UnionBusiness users Other Countries outside the European Union Setup InstallationUnpacking the Monitor Stand method of StandInstallation on wall Detach the hinge cover in the rear of the monitorAttach the hinge cover detached Input Controls and Features11 12 13 15 16 Turns the monitor off standby ‘POWER ON’ button Turns the monitor onCaring for and Cleaning the Monitor Using Your MonitorConnecting the monitor to the PC Turning the Monitor On and OffMenu Operation Using the MenuPC mode analog RGB input Video mode Video, Y/C, or Component inputAdjust the item or change setting of the item Picture ADJ SharpnessLuminance menu Position ADJ DOT Clock Clock PhasePicture ADJ. menu Position ADJ. menuOSD Window menu Color TEMP. menuFunction SEL. menu Reset menuAuto Adjust Using the Monitor in the PC modeMenu flowchart of the Video mode Menu flowchart of the PC mode Basic Connection Example Troubleshooting GD-19L1G GD-17L1G Specifications＜Front View ＞ ＜Side View ＞ Unit：mminch„ Unknown Video Modes Analog RGB Signal „ Video Modes Analog RGB Signal
Top Page Image Contents