Daily Operations / Connections (cont.) | 8 |
7Rear panel
AC inlet
Power input connector. Connect the provided AC power cord to an AC outlet.
• Attach the provided power cord holder to prevent accidental disconnection of the AC power cord (☞ the right).
CAUTION
It is recommended not to use the power cord holder when installing the monitor in a monitor rack etc. where you cannot easily pull out the AC power cord from an AC outlet.
Attaching the Power Cord Holder
•The provided power cord holder prevents accidental disconnection of the AC power cord from the AC inlet.
•The power cord holder consists of two parts, a case and a cover.
1 Attach the power cord holder case | 3 Plug in the AC power cord |
around the AC inlet on the rear | to the AC inlet, and attach |
of the monitor with two screws | the power cord holder |
(provided). | cover to the case. |
Security slot
Install a security wire to this slot.
The illustration of the monitor is of
CAUTION
Use only the provided screws.
2Attach the power cord holder cover to the AC power cord.
CAUTION
A different plug shape will result in the cover being attached to a different position.
CAUTION |
|
Make sure the plug will not be | Tab |
pulled out after the cover is |
|
attached. |
|
NOTE
To detach the cover, release the tab.
1REMOTE (MAKE/TRIG.) terminal
Terminal for controlling the monitor by an external control. ☞ “External Control” on page 14
2REMOTE
Terminals for controlling the monitor by an external control. ☞ “External Control” on page 14
3REMOTE
Terminal for controlling the monitor by an external control. ☞ “External Control” on page 14
4VIDEO (INPUT 1, INPUT 2) terminals (BNC)
Input (IN) and output (OUT) terminals for the composite signals.
5COMPO./RGB (G/Y, B/PB/B-Y, R/PR/R-Y) terminals (BNC)
Input (IN) and output (OUT) terminals for the analog component (color difference) or analog RGB signals.
•Select the signal type in “COMPO./RGB SEL.” corresponding to the type of the input signal (☞ page 10).
6EXT.SYNC (CS) terminals (BNC)
Input (IN) and output (OUT) terminals for the external composite sync (Cs) signals.
• To use these terminals, set “SYNC INPUT SEL.” to “EXT.” ☞ “SYNC FUNCTION” on page 11
NOTE
•The terminals are for all VIDEO (INPUT 1), VIDEO (INPUT 2) and COMPO./RGB.
•When an external sync signal is input, external synchronization has priority over all VIDEO 1, VIDEO 2 and COMPO./RGB input.
•The setting of “SYNC INPUT SEL.” is memorized for each input.
7AUDIO ASSIGN (IN 1, IN 2) terminals (pin jack) Input terminals for the analog audio signals.
•Select the video input to assign the audio signal in “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” (☞ “AUDIO SETTING” on page 11).
8AUDIO ASSIGN (MONITOR OUT) terminals (pin jack)
Output terminals for the analog audio signal.
•The terminals output the audio signal through AUDIO ASSIGN (IN 1) or AUDIO ASSIGN (IN 2) terminals when you select the video input you have selected for “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” in “AUDIO SETTING” (☞ page 11).
•The EMBEDDED AUDIO signal is decoded into an analog signal, then emitted.
NOTE
•The signal is output from this terminal only when the monitor is on.
•The EMBEDDED AUDIO signal has priority over the audio signal input to AUDIO ASSIGN (IN 1) or AUDIO ASSIGN (IN 2) terminals when “SDI 1” or “SDI 2” is selected for “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” and the EMBEDDED AUDIO signal is input to HD/SD SDI (IN 1) or HD/SD SDI (IN 2) terminal.
9HD/SD SDI (IN 1, IN 2) terminals (BNC)
Input terminals for the HD SDI and SD SDI signals.
•The terminals accept also EMBEDDED AUDIO signals* including up to 12 audio channels with the sampling frequency of 48 kHz.
NOTE
The types of signals coming through the IN 1 and IN 2 terminals are automatically
pHD/SD SDI (SWITCHED OUT) terminal (BNC) Output terminal for the HD SDI and SD SDI signals.
•The SDI signal of the current input (SDI 1 or SDI 2) is
NOTE
•When the input other than SDI 1 or SDI 2 is selected, the SDI signal of the input selected last time is
•The signal is output from this terminal only when the monitor is on.
qDVI-D (HDCP) terminal
Input terminal for the
•Select the signal type in “DVI INPUT SEL.” corresponding to the type of the input signal (☞ page 10).
*Using the audio level meter