Onkyo TX-SR504E, TX-SR8450, TX-SR504/B instruction manual Digital Input Signal Formats

Page 57

Advanced Setup—Continued

4	Use the Left and Right [	]/[ ]
	buttons to adjust the speaker
	level, and use the Down [	] but-
	ton to select the next speaker.

The levels can be adjusted from –12 to +12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).

5	Repeat step 4 so that the level of
	Repeat step 4 so that the level of
	the test tone coming from each
	speaker is the same.
	Speakers that you set to No or None in
	the Speaker Conﬁguration (page 34) do
	not output the test tone.

6	Press the [SETUP] button.
	Press the [SETUP] button.
	Setup closes.
	Don’t forget to turn down the volume if
SETUP	you turned it up while setting the levels.

Note:

•A quick way to adjust the speaker levels is to press the remote controller’s [TEST TONE] button to turn on the test tone, use the [LEVEL–] and [LEVEL+] but- tons to adjust the levels, and use the [CH SEL] button to select the speakers.

Digital Input Signal Formats

The following table shows the display indicator for each digital signal format.

Format	Display

Dolby Digital
Dolby Digital


DTS
DTS


PCM			PCM

Normally, the AV receiver detects the signal format auto- matically. However, if you experience either of the fol- lowing issues when playing PCM or DTS material, you can specify the signal format as either PCM or DTS:

•If the beginnings of tracks from a PCM source are cut off, try the PCM setting.

•If noise is produced when fast forwarding or reversing a DTS CD, try the DTS setting.

MASTER VOLUME

TUNING

PRESET

STANDBY/ON

STANDBY

ENTER

MULTI CH

DVD

VIDEO 1

VIDEO 2

VIDEO 3

TAPE

TUNER

C D

RETURN

SETUP

VCR

VIDEO 3 INPUT

PHONES

VIDEO

L AUDIO

R

SPEAKERS

TONE

STEREO

LISTENING MODE

DISPLAY

DIGITAL

DIMMER MEMORY

TUNING

A

B

INPUT

MODE

DIGITAL INPUT

1	Press and hold the AV receiver’s [DIGITAL
	INPUT] button for about 3 seconds.

2	While “Auto” is displayed (about 3 sec-
	onds), press the [DIGITAL INPUT] button

repeatedly to select: PCM, DTS, or Auto.

PCM: Only PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will ﬂash and there will be no sound.

DTS: Only DTS format input signals will be heard. If the input signal is not DTS, the DTS indicator will ﬂash and there will be no sound.

Auto (default): The format is detected automati- cally. If no digital input signal is present, the corresponding analog input is used instead.

57

Image 57

Contents TX-SR504 TX-SR504E TX-SR8450 Avis Important Safety InstructionsPower PrecautionsHandling Notes FCC Information for UserPrecautions Supplied AccessoriesMake sure you have the following accessories Speaker cable labelsFeatures Speaker Sets a and B Enjoying Home TheaterSpeaker Set a Main Room Speaker Set B Sub RoomContents Front Panel Getting to Know the AV ReceiverDisplay Getting to Know the AV ReceiverRear Panel Remote Controller Installing the BatteriesAiming the Remote Controller Remote Controller Using the Remote ControllerRECEIVER/TAPE Mode Remote Mode buttons Listening Mode buttonsButtons used when the Tuner input is selected Buttons used when the Tape input is selectedDVD Mode To select the input source, press CD/MD/CDR/HDD ModeDISC/ALBUM +/- button Arrow / and Enter buttonsSpeaker Connection Precautions Connecting Your SpeakersRead the following before connecting your speakers Speaker ConﬁgurationConnecting Speaker Set a Connecting Your SpeakersConnecting a Powered Subwoofer Connecting Speaker Set BConnecting the Indoor FM Antenna Connecting AntennasConnecting the AM Loop Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor FM Antenna Connecting AntennasConnecting an Outdoor AM Antenna Using a TV/FM Antenna SplitterAbout AV Connections Connecting Your ComponentsOptical Digital Jacks AV Connection Color CodingConnecting Audio and Video Signals to the AV Receiver Connecting Your ComponentsWhich Connections Should I Use? Video Connection FormatsVideo Connection Connecting a TV or ProjectorAudio Connection HintConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback VCRDVD recorder Connecting a Camcorder, Games Console, or Other Device Connecting a VCR or DVD Recorder for RecordingMake the video connection a Make the audio connection a Camcorder or consoleSatellite, cable, set-top box, etc CD Player or Turntable MM with Built-in Phono Preamp Step Connecting a CD Player or TurntableCD in L/R Digital in OpticalReceiver’s Video 2 in L/R jacks and Video 2 in S Jacks Connecting an HDD-compatible ComponentConnecting the Power Cord of Another Component Connecting a Cassette, CDR, MiniDisc, or DAT RecorderConnecting the Power Cord Connecting Onkyo ComponentsAuto Power On/Standby Remote ControlTurning On and Standby Turning On the AV ReceiverSmooth Operation in a Few Easy Steps Have you connected a component to a digital audio input?First Time Setup Assigning Digital Inputs to Input SourcesChanging the Input Display Minimum Speaker Impedance Setup not North American model First Time SetupTesting the Speakers Press the Setup buttonUse the Down button to Left and Right / but- tons to select 2ch or 1chPlaying Your AV Components Select a suitable listening mode and enjoyBasic AV Receiver Operation Start playback on the source componentUsing the Multichannel DVD Input Playing Your AV ComponentsDisplaying Source Information Tuning into AM/FM Radio Stations Listening to the RadioListening to AM/FM stations Listening to the Radio Presetting AM/FM Stations and XM ChannelsUsing RDS European Models Only What is RDS?RDS Program Types PTY Displaying Radio Text RT Finding Stations by Type PTYListening to Trafﬁc News TP Listening to XM Satellite Radio North American Models Only Connecting the XM Passport SystemSelecting XM Satellite Radio Press the Tuner input selectorSelecting XM Radio Channels Signing Up for XM Satellite RadioDisplaying XM Radio Information Positioning the XM Passport System XM Radio MessagesOn the AV receiver, press Buttons to select 5. ANT AimSetting the Display Brightness Adjusting the Bass and TrebleCommon Functions Muting the AV ReceiverAdjusting Speaker Levels Using the Sleep TimerUsing Headphones Common FunctionsSelecting with the Remote Controller Using the Listening ModesSelecting Listening Modes Selecting on the AV ReceiverDVD Using the Listening ModesDTS About the Listening ModesOnkyo Original DSP Modes Use this mode with any stereo movie e.g., TV, DVD, VHSUsing the Late Night Function Dolby Digital only Using the CinemaFILTERUsing the Audio Adjust Settings Plii and PLIIx Music Mode Settings Input Channel SettingsDTS Neo6 Music Mode Setting Dolby Digital EX Input Signal Setting Recording Recording the Input Source Recording Audio and Video from Separate Sources Advanced Speaker Settings Advanced SetupCrossover Frequency Double BassAdvanced Setup Speaker DistanceSpeaker Levels Digital Input Signal Formats Mode button Correcting Sound and Picture SyncInput Selector Controlling Other Components Entering Remote Control CodesResetting Remote Mode Buttons Remote Control Codes for Onkyo Components Connected viaResetting the Remote Controller Controlling Other ComponentsON/STANDBY, TV TV VOLCH + Troubleshooting PowerAudio Troubleshooting VideoTuner Remote Controller RecordingOthers Video ATT0 default Setting Press the Setup button when you’ve ﬁnishedVideo Attenuation Video ATT2 Gain is reduced by 2 dBAmpliﬁer Section SpeciﬁcationsVideo Section Tuner SectionMemo Onkyo Europe Electronics GmbH Onkyo U.S.A. CorporationOnkyo Europe UK Office Onkyo China LimitedMode intryckt och tryck samtidigt in knappen Manteniendo pulsado el botón Remote ModeHalten Sie die änderungsbedürftige Remote DISPLAY-Taste 3 Sekunden lang betätigenTV/DVD Combination DVD CodesCD Recorder CD/MD/CDR/HDD Codes CDMD Recorder HDD PlayerTV Codes GPM GECHCM ICENTC NEISBR SEGTVS TMKABS VCR CodesHI-Q MEIDBS/PVR Combination PVRTV/VCR Combination Cable Converter CABLE/SAT CodesCable/PVR Combination Satellite ReceiverQNS HTSTPS UEC3 4 4 1 8 8 a