Onkyo TX-DS595 Using a Macro function, Programming a Macro function, Running a Macro function

Using a Macro function

What is a Macro function?

A Macro function enables you to program a series of button operations (up to 16) on the remote controller into a single button. For example, to play a compact disc player connected to the TX- DS595 normally, you must perform the following steps:

1.Press the RCVR MODE button.

2.Press the ON button.

3.Press the CD (INPUT SELECTOR) button.

4.Press the CD MODE button.

5.Press the playback () button.

By using the macro function, you can perform the above five operations by only pressing two buttons.

Programming a Macro function

You can program a different macro into the MODE MACRO button for each of the eight MODE buttons. The macro is then executed by pressing the appropriate MODE button and then pressing the MODE MACRO button. For example, to program the macro described above into the CD MODE button, perform the steps given below.

1. Press and hold down the desired MODE button (in

this case, the CD MODE button), press the MODE

MACRO button, and then release both buttons.

When you press the CD MODE button, the SEND/LEARN

indicator lights and the CD MODE button lights green. When

you press the MODE MACRO button, the indicator turns off.

When you release the buttons, the indicator flashes and lights

again.

2. Press the operation buttons you wish to program in

order (in this case, press RCVR MODE → ON → CD

(INPUT SELECTOR) → CD MODE → playback ( )

button).

ON

RCVR MODE

SEND/ LEARN

PREPROGRAMME						D	A
							& LE RNING CAPABILITY
	P			ON			STDBY
EE
SL
						MACRO
	T									MO
	EC				MODE						DE
DIR
				CD			DVD
	VR									M	D
RC
					LE		V
			CAB				CR
	T									T
	A									V
S
				UR			SE
				T	N			TU
		RE							P
CH										VOL
DISC
		T	C	H S				T
AUDIO		OP			EL		T		U	MUTING
				MENU			MEN
		ANGLE					SUBTITLE
TV/VCR						LEVEL
RANDOM									OPEN / CLOSE
		REC
		I				SELECTOR
		NPUT
DVD										CD
	V 1			V 2			T1			T 2
	V 3			V 4			TUN			PH
	STEREO				DIRECT					DSP
		1					2			3
	SURR						A.ST			DSP
		4					5			6
	SP A						SP B			Re-EQ
		7					8			9
	DISPLAY				DIMMER					ZONE 2
	+10						0			SEARCH
	-- / ---									ENTER

HOME THEATER CONTROLLER

RC-447M

MODE MACRO

CD MODE

(CD playback)

CD (INPUT SELECTOR)

	When you press each button, the SEND/LEARN indicator turns
	off. When you release the button, the indicator lights.
3.	Press the MODE MACRO button to complete the
	programming.
	The SEND/LEARN indicator flashes twice slowly.
4.	Run the macro to check to see if the macro has been
	properly programmed.

Notes:

•You may program up to 16 button operations into each macro function. If you try to program a 17th operation, it will be ignored, and programming is stopped.

•If no button is pressed for more than 30 seconds during the programming, the SEND/LEARN indicator flashes three times quickly, and the remote controller exits the programming mode. Resume from Step 1.

•If you perform an invalid operation during programming, the SEND/LEARN indicator flashes three times quickly, and the remote controller exits the programming mode. Resume from Step 1.

Running a Macro function

Tips:

•If you erase or change the command of a button programmed in a macro, that operation of that button will no longer work in the macro. In this case, it will be necessary for you to reprogram the macro in order to avoid incorrect operation.

•The codes programmed into a macro will be transmitted at an interval of 0.5 seconds. However, some devices may not be able to complete one operation in 0.5 seconds and may miss the next code. In this case, after pressing one operation button, you can press the same MODE button again before pressing the next operation button to add another 0.5 seconds between the two operations.

Perform the procedure below to run a macro function that you have programmed into the remote controller. After programming a macro, you should always run it at least once to make sure that it has been programmed properly.

1.Point the remote controller at the TX-DS595 and press the CD MODE button.

2.Press the MODE MACRO, and verify that the devices operate properly.

It may take a while for the macro to finish transmitting, so be sure to continue pointing the remote controller at the device until the SEND/LEARN indicator turns off.

45