Sharp PG-F212X-L Overloading, Object and Liquid Entry, Servicing, Damage Requiring Service, Heat

Page 11

15.Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

16.Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

17.Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18.Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the product.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

e.If the product has been dropped or damaged in any way.

f.When the product exhibits a distinct change in performance, this indicates a need for service.

19.Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

20.Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21.Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22.Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Introduction

¥DLP¨ and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a trademark of Texas Instruments.

¥Microsoft¨ and Windows¨ are registered trademarks of Microsoft Corporation in the United States and/or other countries.

¥PC/AT is a registered trademark of International Business Machines Corporation in the United States.

¥Adobe¨ Reader¨ is a trademark of Adobe Systems Incorporated.

¥Macintosh¨ is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.

¥All other company or product names are trademarks or registered trademarks of their respective companies.

¥Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.

7

Image 11
Contents PG-F212X-L Model No Serial No If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage A. only IntroductionENGLISHOnly InformationFor Future Reference Maintenance Troubleshooting IndexContents Reference Power-Cord Protection CleaningAccessories Power SourcesOverloading Damage Requiring ServiceReplacement Parts Safety CheckSee ÒRegarding the LampÓ on Avoid locations with extremes of temperatureRest your eyes occasionally Do not block the exhaust and intake ventsOther connected equipment Using the projector in other countriesTemperature monitor function If the projector starts to overheat due to setupOptional accessories AccessoriesProjector Part Names and FunctionsAudio OUT Rear ViewAudio 1 input terminal ComputerButton COMPUTER, DVIUP/PAGE CLICK/EFFECTInserting the Batteries Usable Range Height Setup and ProjectionQuick Start Control Upper sideCeiling-mount Setup Setting up the ProjectorSetting up the Projector Standard Setup Front Projection120 Projection PRJ ModeExample Normal Mode Picture Size Screen Size and Projection Distance Normal ModeStretch Mode You may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Audio OUT Controlling the Projector by a Computer Connecting the Power CordAC socket To AC outlet Power cord supplied On-screen display confirmation message Lamp indicator Power indicator STANDBY/ON buttonTurning the Projector On/Off Turning the Projector onImage Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Adjusting the Picture SizeUse the rear adjustment foot to make the projector level Adjusting the HeightShrinks upper side Move the slide bar in the + direction Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionCOMPUTER, DVI VIDEO, Video Switching the Input ModeAdjusting the Volume Buttons AV Mute button VOL +/- Volume buttonsResize Resize ModePress Resize About Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionDisplaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImageWhen right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clickingFollowing shows the items that can be set in the projector Menu ItemsScreen adjustment SCR-ADJ menu ÒHelpÓ menu n Items you can set with the Help menuExample Adjusting ÒBrightÓ Using the Menu ScreenMenu Selections Adjustments Press Qor Oand select Picture to adjustPress Enter To adjust the projected image while watching itPress P or R and select Bright to adjust Press O or Q to adjust the item selectedPAGE1 PAGE2 Picture Adjustment Picture Menu1Selecting the Picture Mode Menu operation nAdjusting ÒHueÓ, ÒSaturationÓ, or ÒValueÓ 2Adjusting the Image4Adjusting the Colors 3Adjusting the Color TemperatureReducing Image Noise DNR Lamp SettingProgressive 4Setting the On-screen Display Adjusting the Projected Image SCR ADJ Menu1Setting the Resize Mode 2Adjusting the Image Position 3Keystone Correction8Selecting the On-screen Display Language 6Selecting the Setup Guide5Selecting the Background Image Reversing/Inverting Projected Images6Speaker Setting 2Auto Power Off Function4STANDBY Mode 5Setting the Confirmation Sound System SoundSelect System Lock, then press Enter or Q 9Fan Mode Setting7Audio Input 0System Lock FunctionLocking the Operation Buttons Keylock FunctionChecking the Lamp Life Status Enter the same keycode in Re- confirmUtilizing the Help Menu Functions Troubleshooting with the Help MenuEnter button Adjustment buttons P/R/O/Q MENU/HELP button Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer Storing the Projector How to Use the Storage CaseSub 15 pin female connector Connecting Pin AssignmentsUSB Terminal Type B USB connector RS-232C Terminal mini DIN 9 pin female connectorBasic format RS-232C Specifications and CommandsComputer control Communication conditionsComputer Projector CommandsRS-232C Specifications and Commands BrilliantColorTM OK or ERR PAL Computer Computer Compatibility Chart21-24 Troubleshooting49, 50 For Sharp Assistance Specifications Dimensions Index