Sharp PG-F262X, PG-F212X quick start This Apparatus Must be Earthed

Page 3

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat- ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used.

Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.

In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi- ately and disposed of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the instructions below:

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code: Green-and-yellow : Earth

Blue

: Neutral

Brown

: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

iii

Image 3
Contents PG-F312X PG-F262X PG-F212X Model No Serial No If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage A. only IntroductionENGLISHOnly InformationFor Future Reference Using the Menu ScreenContents Reference Power-Cord Protection CleaningAccessories Power SourcesOverloading Damage Requiring ServiceReplacement Parts Safety CheckSee Replacing the Lamp on Avoid locations with extremes of temperatureRest your eyes occasionally Do not block the exhaust and intake ventsUsing the projector in other countries Temperature monitor functionOther connected equipment Optional accessories AccessoriesProjector Part Names and FunctionsAudio OUT Rear ViewAudio 1 input terminal ComputerButton COMPUTER, DVIUP/PAGE CLICK/EFFECTInserting the Batteries Usable Range Setup and Projection Quick StartHeight Control Upper sideCeiling-mount Setup Setting up the ProjectorSetting up the Projector Standard Setup Front ProjectionProjection PRJ Mode Example Normal Mode Picture Size120 Normal Mode Stretch ModeScreen Size and Projection Distance You may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Audio OUT Connecting the Power Cord AC socket To AC outlet Power cord suppliedControlling the Projector by a Computer On-screen display confirmation message Lamp indicator Power indicator STANDBY/ON buttonTurning the Projector On/Off Turning the Projector onImage Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Adjusting the Picture SizeUse the rear adjustment foot to make the projector level Adjusting the HeightShrinks upper side Move the slide bar in the + direction Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionCOMPUTER, DVI VIDEO, Video Switching the Input ModeAdjusting the Volume Buttons AV Mute button VOL +/- Volume buttonsResize Mode Press ResizeResize About Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionDisplaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImageWhen right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clickingFollowing shows the items that can be set in the projector Menu ItemsScreen adjustment SCR-ADJ menu Help menu n Items you can set with the Help menuExample Adjusting Bright Using the Menu ScreenMenu Selections Adjustments Press Q or O and select Picture to adjustPress Enter To adjust the projected image while watching itPress P or R and select Bright to adjust Press O or Q to adjust the item selectedPAGE1 PAGE2 Picture Adjustment Picture Menu1Selecting the Picture Mode Menu operation nAdjusting Hue, Saturation, or Value 2Adjusting the Image4Adjusting the Colors 3Adjusting the Color TemperatureLamp Setting ProgressiveReducing Image Noise DNR Setting the On-screen Display Adjusting the Projected Image SCR ADJ MenuSetting the Resize Mode Adjusting the Image Position Keystone CorrectionReversing/Inverting Projected Images Selecting the Setup GuideClosed Caption Selecting the Background Image5Setting the Confirmation Sound System Sound 1Auto Sync Auto Sync Adjustment2Auto Power Off Function 4STANDBY ModeSelect System Lock, then press Enter or Q 9Fan Mode Setting7Audio Input 0System Lock FunctionLocking the Operation Buttons Keylock FunctionChecking the Lamp Life Status Enter the same keycode in Re- confirmTroubleshooting with the Help Menu Enter button Adjustment buttons P/R/O/Q MENU/HELP buttonUtilizing the Help Menu Functions Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Storing the Projector How to Use the Storage CaseSub 15 pin female connector Connecting Pin AssignmentsUSB Terminal Type B USB connector RS-232C Terminal mini DIN 9 pin female connectorBasic format RS-232C Specifications and CommandsComputer control Communication conditionsProjector CommandsRS-232C Specifications and Commands BrilliantColorTM OK or ERR CC1 Computer Computer Compatibility Chart21-24 Troubleshooting49, 50 For Sharp Assistance Specifications Dimensions Index