NAD T752 owner manual Using the T, Selecting Sources, Adjusting the Volume, Muting the Sound

Page 18

USING THE T 752

You may operate the T 752 receiver from its front panel or via the HTR 2 remote control. Since the remote will be the primary controller for most cases, we will focus on remote-controlled operations. Be sure also to read the section, "Front Panel" above.

SELECTING SOURCES

With the HTR 2’s remote's [Amp] device selected, the remote’s numeric-key section directly selects the receiver’s inputs, plus the internal tuner ([Tuner), Tape Monitor ([Tape]), and multichannel input ([Ext. 7.1/ 5.1]) refer to the red labels directly above each key.

•When an audio-only source (CD, DISC, TUNER) is selected, the most recently-selected video signal remains selected, until another audio-video input is selected

•When you change sources, the VFL will display the new input in its primary display.

•A newly selected input's listening mode (Stereo, EARS, Pro Logic II, etc.) will revert to the mode to which it is configured on the <Input Settings> line of the setup menu, unless the incoming signal is a Dolby Digital or DTS source, in which case the input will be set automatically to the appropriate decoding mode.

ADJUSTING THE VOLUME

Use the HTR 2 remote's <Volume up/down> keys to adjust the "master volume" of the T 752, raising or lower all channels together. Note that:

•A momentary keypress will change the master volume by 1 dB increments; if you hold down <Volume up/ down> the master-volume change will "run-on" until the key is released.

•The T 752's OSD will show the volume setting as a line graphic with a numeric display above in dB relative to the reference level.

Since recordings vary considerably in overall average level, there is no imperative to listen at any particular master-volume setting. A setting of -20 may sound "as loud" from one CD or DVD as -10 does from another.

•If muting has been activated (below), adjusting master-volume via the HTR 2 remote or the front-panel knob automatically releases the mute function.

•The T 752 will power-up from Standby mode at whatever master volume setting was last used; however, if the prior setting was greater than –20 dB the T 752 will power up to –20 dB. This prevents inadvertently beginning a session at excessive volume.

MUTING THE SOUND

Use the HTR 2 remote's <Mute> key to silence all channels completely. Muting is always available, regardless of source or listening mode selections. Note that:

•Cycling through Standby or powering off does not release muting; the T 752 will return from Standby with muting on if Standby was invoked with muting on.

•Changing input or listening-mode selections does not release muting.

•Adjusting the master-volume upward via the HTR 2 or the front-panel knob automatically releases the mute function.

LISTENING TO RADIO

The T 752’s internal AM/FM tuner offers very high quality sound from radio broadcasts. Note that reception and sound quality will always be dependent to a degree on the type of antenna(s) used, as well as proximity to the broadcast origin, geography, and weather conditions.

1 8

Page 17 Page 19
Image 18
Page 17 Page 19
Contents English Precautions Safety InformationExplanation of Graphical Symbols InstallationDamage Requiring Service Electric PowerMaintenance Do not Attempt to Service the Unit Yourself OWNER’S RecordTable of Contents Getting the Most from the NAD T Thank you for choosing NADUnpacking and Setup WHAT’S in the BOXChoosing a Location Ease of USE About the TR.S., Matrix and Digital Surround IntegrationAbout the HTR 2 System Remote Control UpgradabilityQuickstart Play a DVD MovieFront Panel Digital Input Jack Default Assignment Rear Panel 13 12V Trigger IN/OUT Setting UP the T Getting StartedDealing with HUM and Noise Display the OSD Input SetupAbout the ON-SCREEN Displays OSD and FRONT-PANEL Readout Navigating the OSD and Making ChangesCHANNEL-BALANCE Test Setup Speaker SetupListening Mode Using AN SPL MeterRecalling Presets Creating and Using PresetsCreating Presets Speaker DistanceSelecting Sources Using the TAdjusting the Volume Muting the SoundSelecting Radio Presets Tuning StationsSetting Radio Presets Choosing the FM Mute / ModeAbout the T 752S Listening Modes Displaying the Signal Mode Selecting Listening ModesAdjusting Listening Modes Adjusting Channel Levels on the FLYAdjusting the Tone Controls Controlling the T Using the HTR 2 Remote ControlSpecifications Learning Codes from Other RemotesPUNCH-THROUGH Copy a Command from Another KEYMacro Commands Recording MacrosDelete Mode KEY-ILLUMINATION TimeoutFactory Reset Loading CODE-LIBRARIESChecking CODE-LIBRARY Number Search ModeTrigger Setup Summary of HTR 2 ModesTroubleshooting Condition Possible Causes Possible SolutionssAV Surround Sound Receiver SpecificationsPhysical Specifications Amplifier SectionNAD

T752 specifications

The NAD T752 is a highly regarded audio/video receiver that has made its mark in the realm of home theater systems. Known for its versatility, performance, and value for money, the T752 is designed to meet the needs of both casual listeners and serious audiophiles. With its robust array of features and technologies, the T752 provides a comprehensive solution for enjoying movies, music, and gaming with impressive clarity and power.

One of the standout features of the NAD T752 is its multi-channel amplification. It delivers a powerful 5.1 channel surround sound experience, allowing users to immerse themselves in rich audio. Each channel is designed to provide a 50 watts output, ensuring sufficient power for driving a variety of speakers while maintaining distortion-free sound.

The T752 incorporates NAD's proprietary PowerDrive technology, which optimizes the performance of the amplifier under different loads. This means that the receiver can efficiently drive low-impedance speakers without sacrificing sound quality or risking damage. This technology is crucial for delivering consistent performance across various listening environments.

In terms of connectivity, the NAD T752 is equipped with a wide range of inputs and outputs, including multiple HDMI ports, composite and component video inputs, and digital audio inputs. This ensures compatibility with a variety of source devices, from Blu-ray players to gaming consoles, making it a versatile addition to any home theater setup. The HDMI connectivity allows for direct switching between devices while also supporting high-definition video and audio formats.

The T752 also features advanced processing capabilities, such as Dolby Digital and DTS decoding, which enhances the surround sound experience, making dialogue clearer and effects more immersive. NAD’s proprietary EISA Award-winning technology further enriches audio playback, ensuring the listener receives a captivating surround sound experience.

Another noteworthy characteristic of the NAD T752 is its user-friendly interface. The receiver is designed for ease of use, with intuitive controls and an on-screen display that simplifies the setup process. Additionally, NAD offers a comprehensive remote control that allows users to manage their listening experience seamlessly.

In conclusion, the NAD T752 stands out as a solid choice for home theater enthusiasts. With its robust sound performance, extensive connectivity options, and advanced audio processing technologies, it delivers a rewarding listening experience. Whether watching films, listening to music, or gaming, the T752 is capable of elevating your entertainment experience to new heights.
Top Page Image Contents