Sharp PG-A20X Rest your eyes occasionally, Avoid locations with extremes of temperature

Page 12

IMPORTANT SAFEGUARDS

Be sure to read the following safeguards when setting up your projector.

Caution concerning the lamp unit

■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for a replacement.

See “Replacing the Lamp” on page 57.

BQC-PGA20X//1

Caution concerning the setup of the projector

■For minimal servicing and to maintain high image qual- ity, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environ- ments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.

■Be sure that the intake vent and the exhaust vent are not obstructed.

■If the cooling fan becomes obstructed, a protection cir- cuit will automatically put the projector into the standby mode. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

Caution regarding transportation of the projec- tor

■When transporting the projector, be sure not to subject it to hard impact and/or vibration, as this can result in damage. Take extra care with the lens. Before moving the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables con- nected to it.

Do not set up the projector in places exposed to direct sunlight or bright light.

■Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the cur- tains and dim the lights when setting up the screen in a sunny or bright room.

The projector may be safely tilted to a maximum angle of 12 degrees.

■Placement should be within ±12 degrees of horizontal.

Do not subject the projector to hard impact and/ or vibration.

■Take care with the lens so as not to hit or damage the surface of the lens.

Rest your eyes occasionally.

■Continuously watching the screen for long hours will cause eye strain. Be sure to occasionally rest your eyes.

Avoid locations with extremes of temperature.

■The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

■The storage temperature of the projector is from

–4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.

■Allow at least 7 7/8 inches (20 cm) of space between the exhaust vent and the nearest wall or obstruction.

-8

Other connected equipment

■When connecting a computer or other audio-visual equipment to the projector, make the connections AF- TER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be con- nected.

■Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.

Using the projector in other countries

■The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector over- seas, be sure to use an appropriate power cord for the country you are in.

Temperature monitor function

■If the projector starts to overheat

due to setup problems or block-

age of the air vents, “ ” and

“ ” will illuminate in the lower left corner of the picture. If the temperature continues to rise, the lamp

will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cooling-off period the projector will enter the standby mode. Refer to “Maintenance Indicators” on page 55 for details.

Info

•The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.

•Do not unplug the power cord during projection or cool- ing fan operation. This can cause damage due to rise in internal temperature, as the cooling fan also stops.

PG-A20X_E_PDF_P06_14.p65

8

03.4.23, 9:55 AM

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PG-A20X Model No. PG-A20X Serial No Special Note for Users in the U.K 03.4.23, 954 AM Introduction When Attaching the Quick Guide Label Product DisposalOutstanding Features Light and Compact DesignContents Appendix Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check Wall or Ceiling MountingAvoid locations with extremes of temperature Using the projector in other countriesTemperature monitor function Rest your eyes occasionallyTo install Acrobat Reader from the CD-ROM For other operating systems For other languagesFor Windows For MacintoshPart Names Projector Front and Top ViewUsing the Kensington Lock Projector Rear ViewRemote Control Front View FORWARD/BACK buttonsUsing the Remote Control When using the remote controlUsable Range Inserting the BatteriesAccessories Supplied accessoriesOptional accessories Connecting the Projector to Other Devices Before ConnectingConnecting the Power Cord This projector can be connected toConnecting to a Computer Using the RGB Cable Ferrite corePlug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Connecting to Component Video Equip- ment CableControlling the Projector Using a Computer Setup Using the Adjustment FeetRear adjustment foot on the bottom Foot release Projector as well Front adjustment feetAdjusting the Lens Focus ring Zoom knobSetting up the Screen Standard Setup Front ProjectionNormal Mode Stretch ModeScreen Size and Projection Distance Projecting a Reversed/Inverted Image Projection from behind the ScreenBasic Procedure Plug the power cord into the wall outletPress on the projector or on the remote control Image ProjectionPress , or on the remote control to select the IN- PUT mode Control to adjust the volumePress On the remoteTurning the Power off Selecting the On-screen Display LanguagePress , , \ and to adjust the Keystone correction Keystone Correction Correcting Trapezoidal DistortionCorrecting Trapezoidal Distortion Keystone buttonMenu Items Main menu Sub menuInput 2 / 3 Mode Main menuUsing the Menu Screen AdjustmentsMenu Selections Press \or to display the otherPress or to select the item you want to adjust Press \ or to adjust the item selectedSettings Press \or to display the other menu screensButton Menu button \, buttons Menu iconsSub menu Picture Adjustment Adjusting the ImageCLR Temp Adjusting Color Temperature SRGB sRGB Setting Signal Type Signal Type SettingMemory Storing and Selecting Adjustment Settings Gamma Gamma CorrectionComputer Image Adjustment Adjusting the Computer Special Modes Special ImageExample Fine Sync menu screen for Input 1 mode Mode SettingsAuto Sync Auto Sync Adjust- ment Signal Info Checking the Input SignalAuto Sync button Picture Display Mode Switching the Picture Dis- play ModeButton Resize button Functions Press to cancel the operation Still and Zoom ImageButton Buttons EnlargeLocking the Operation But- tons Taking the Keylock offHold down on the projector for about 3 seconds Using the Options Menu Lamp Timer Life CheckKeystone Setting the Key- stone Correction Mode Description of Keystone Correction ModeVideo System Setting OSD Display Setting On- screen DisplayEco Mode Setting the Eco Mode Video SystemAuto Power Off Auto Power Off FunctionMenu Position Selecting Menu Screen PositionPassword Setting a Pass- word If You Forget Your Pass- wordAnti-TheftSetting the Anti-Theft Easy to Use Functions Setting the Projection Mode Reversing/Inverting Projected ImagesHow to Use Carrying Case Carrying the ProjectorLens cap Maintenance Cleaning the projectorCleaning the lens Cleaning the exhaust and intake ventsCleaning and Replacing the Air Filter Replacing the Air FilterClean the air filter Tab User service screwReplace the air filter Replace the filter/lamp unit coverMaintenance Indicators About the lamp indicatorAbout the temperature warning indicator Maintenance Indicators Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Standby button AC socket User Service Screw TabChange the air filter Resetting the Lamp Timer Connect the power cordReset the lamp timer Remove the lamp unitConnecting Pin Assignments RGB Input Component InputRS-232C Specifications and Command Settings CommandsPC control Communication conditionsComputer Compatibility Chart ComputerTroubleshooting 16-20Troubleshooting For Sharp Assistance Specifications NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAMDimensions Units inches mmGlossary Anti-TheftIndex BorderSharp Corporation

PG-A20X specifications

The Sharp PG-A20X projector is a compact and versatile projection solution designed for both business and educational environments. Known for its high-quality performance, the PG-A20X integrates advanced technologies that deliver sharp images and vibrant colors, making it ideal for presentations, lectures, and multimedia content.

One of the standout features of the Sharp PG-A20X is its impressive brightness, rated at 2000 lumens. This brightness ensures clear visibility even in well-lit rooms, allowing users to present effectively without dimming the surroundings. The projector also utilizes a high contrast ratio, typically around 2000:1, which enhances the depth and detail of images, providing a more engaging viewing experience.

The PG-A20X employs DLP (Digital Light Processing) technology, renowned for its reliability and picture quality. DLP projectors typically offer superior color accuracy and smooth motion, making the PG-A20X suitable for displaying video content as well as static images. In addition to vibrant colors, the unit’s sharpness and clarity are crucial for text-heavy presentation slides, ensuring that every detail is easily legible.

Portability is another key characteristic of the PG-A20X. Weighing around 3 kg, it is lightweight and easy to transport, making it an ideal choice for professionals who frequently move between locations. Its compact design also allows for straightforward setup in various environments, from classrooms to conference rooms.

Connectivity options are extensive, featuring HDMI, VGA, and audio input, which accommodate a wide range of devices, from laptops to DVD players. The projector also supports various formats, ensuring compatibility with different media. The integrated speaker, while small, adds convenience for presentations that do not require elaborate sound setups.

Furthermore, the Sharp PG-A20X boasts a long lamp life, often exceeding 3000 hours in standard mode. This longevity not only reduces the total cost of ownership but also minimizes maintenance frequency, allowing users to focus more on their presentations rather than on equipment upkeep.

In summary, the Sharp PG-A20X projector is characterized by its high brightness, DLP technology, portability, versatile connectivity, and long lamp life. These features make it a reliable choice for anyone looking to deliver impactful presentations in a variety of settings. Whether in the boardroom or the classroom, the PG-A20X stands out as a trusted companion for effective communication.
Top Page Image Contents