Vidikron 90 manual Operation

Page 48

Operation

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

•Menu Mode: This is the manner in which the OSD menus appear and disappear when you press MENU. Choose one of the following:

0 = No transition; menus abruptly appear and disappear.

1 = Menus fade in and out.

2 = “Checkerboard” dissolve; menus appear and disappear in sections.

3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right, and retract in the opposite direction.

•Timeout - Short/Long: These settings control how long the OSD menus stay on screen. Select a time-out period of from 2 to 60 seconds.

•Side Bar Color: This controls the color of the inactive image area. The range is from -100 (black) to 100 (white).

The inactive image area is on either side of the active image area when using the Standard 4:3 aspect ratio, and above and below the active image area when using the Letterbox aspect ratio.

System Reset: To reset ALL projector settings (including image settings) back to their factory defaults, choose System Reset from the Service menu. Select Confirm to continue or Back to cancel. This action is not undoable. Use it with caution!

4-14	Vidikron Vision Model 90 Owner’s Operating Manual

Image 48

Contents DLP Projector Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial Communications1List of Figures List of Figures 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories 2Controls and Functions Vision 90 at a GlanceComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsVision 90 Rear Panel Volt 800 mA Trigger Outputs Video 1 / S-VIDEOVision 90 Remote Control Vision 90 Remote Control FunctionsMemory Preset Buttons ISF NT Night On / OFFCursor Keys CustVideo Comp ComponentHD 1 4 / HD 2 DVI 1 6 / DVI 23Installation Remote ControlQuick Setup Installation OverviewStep Procedure For Details Refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsFlat vs. Curved Screens Ambient Light Estimating Throw DistanceVision 90 Lens Options Vertical and HorizontalPosition Throw Ratio Throw Distance RangeShift Vertical Lens ShiftAdjusting the Projection Vertical and Horizontal Lens Shift LimitsAngle Lens OptionFolded Optics Connections to the Vision DVI Connections See FigureDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 10. Composite, S-Video and Component Video ConnectionsConnecting 12-Volt Trigger ConnectionComponents Turning on the Power Adjusting the Picture Orientation4Operation Lens Adjustments Using the On-Screen MenusFocus Zoom Shift ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Input Source Composite Video Component SDAspect Ratio Settings DescriptionPerform the adjustments in the order listed here PicturePicture Brightness Contrast Color Tint Sharpness Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets InformationCalibration Should be used by ISF-certified technicians onlyOperation Service Code sent by the remote to match as described below Operation 5Maintenance and Troubleshooting Lamp Replacement Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionMaintenance and Troubleshooting Serial Command Syntax Serial CommandsRS-232 Connection and Port Configuration Command Parameter Value Description Min/max Stored?Serial Communications CUSTOM1 YES Command Parameter Value Description Min/max 7Specifications Vision 90 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsLimited Warranty Specifications are subject to change without noticeRegulatory Approvals Vision 90 Dimensions Vision 90 DimensionsPage RUMA-011150