Allied Telesis AT-8100L/8POE-E, AT-8100S/48POE manual Choosing a Site for the Switch

Page 63

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches

Choosing a Site for the Switch

Observe these requirements when planning the installation of the switch.

If you plan to install the switch in an equipment rack, the rack should be safely secured so that it will not tip over. Devices in a rack should be installed starting at the bottom, with the heavier devices near the bottom of the rack.

If you plan to install the switch on a table, the table should be level and stable.

The power outlet should be located near the switch and be easily accessible.

The site should allow for easy access to the ports on the front of the switch, so that you can easily connect and disconnect cables, and view the port LEDs.

The site should allow for adequate air flow around the unit and through the cooling vents on the front and rear panels. (The ventilation direction in units that have a cooling fan is from front to back, with the fan on the back panel drawing the air out of the unit.)

The site should not expose the switch to moisture or water.

The site should be a dust-free environment.

The site should include dedicated power circuits or power conditioners to supply reliable electrical power to the network devices.

The site should not be a wiring or utility box because the switch will overheat and fail from inadequate airflow.

Warning

Stand-alone switches should not be stacked on top of one another on a table or desktop because that could present a personal safety hazard if you need to move or replace switches.

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Stand-alone Switch Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Snmp 110 Contents Figures Figures Tables Tables Preface Document Conventions Contacting Allied Telesis Preface Chapter OverviewFeatures 10/100 Mbps Twisted Pair Ports8100L and 8100S Models 10/100/1000 Mbps Twisted Pair Ports SFP Slots Power over EthernetOverview Page 8100L Series Switches Hardware FeaturesFeature Front Panel Components Front Panels of the 8100L Series SwitchesFeature 24C 8100S Twisted Pair Series SwitchesFront Panels of the 8100S Twisted Pair Series Switches Networking Ports and SFP Slots on the 8100S Series Switches Feature 16F8-SC 16F8-LC 24F-LC 8100S Fiber Optic Series SwitchesFront Panels of the 8100S Fiber Optic Series Switches AT-8100S/24-LC 100Base-FX Fiber Back Panels AT-8100L/8POESwitchShows the back panels of the dual power supply switches Series Management Panel Management PanelsConvention Definition Model Naming ConventionsThis is the number of 100Base-FX fiber optic ports 10/100Base-TX Twisted Pair Ports Speed Duplex Mode Wiring ConfigurationDistance Requirements10Mbps 100Mbps Cable Type Non PoE PoE+ 10/100/1000Base-T Twisted Pair Ports Cable Type 10Mbps 100Mbps 1000Mbps Cable Requirements Port PinoutsModel 10/100/1000 SFP Slot Base-T Port SFP SlotsOverview Power Over Ethernet Power Budget Powered Device ClassesMaximum Power Class Output from a Switch PD Power Range Port Prioritization Wiring Implementation Stacking Ports Eco-friendly Button LEDs 10/100Base-TX Twisted Pair Port LEDsState Description 10/100/1000Base-T Twisted Pair Port LEDs Base-FX Port LED 100Base-FX port LED is described in Table 100Base-FX Port LEDsSFP Slot LEDs SFP slot LED is described in Table LINK/ACT Stacking Port LEDsStack ID Console Port Power Supplies Power Connectors Overview Beginning the Installation Installation Procedures Reviewing Safety Precautions Beginning the Installation Page Beginning the Installation Choosing a Site for the Switch 8100L Series Switches Unpacking the SwitchComponents of the 8100L Series Switches Components of the 8100S Series Switches 8100S Series SwitchesComponents of the AT-8100S/24C Switch AT-8100S/24C SwitchBeginning the Installation Installing the Switch on a Table or in an Equipment Rack Installing the Switch on a Table or Desktop Removing the Rubber Feet Installing the Switch in an Equipment RackInstalling the Switch on a Table or in an Equipment Rack Page Installing the Switch on a Table or in an Equipment Rack Page Installing the Switch on a Table or in an Equipment Rack Cabling the Networking Ports Twisted Pair Ports Cabling the Twisted Pair and Fiber Optic PortsFiber Optic Ports General Guidelines Installing Optional SFP Transceivers Page Positioning the SFP Handle in the Upright Position Page Cabling the Networking Ports Powering On the Switch Plugging in the AC Power Cord Powering On an AC SwitchMonitoring Initialization Processes LEDs Phase SecondsInitialize Management Load SoftwareSwitch Initialization Messages Initializing Monitor Powering On a DC Switch DC Terminal Block Page Powering On the Switch Starting a Local Management Session Setting the Stack ID NumberStarting a Telnet Management Session Stack oldid renumber newid Changing the Stack ID NumberThis confirmation prompt in is displayed Local Management Telnet Management Starting a Management SessionSecure Shell Management Web Browser Management Snmp 102 Troubleshooting 104 105 Troubleshooting 106 Technical Specifications Physical SpecificationsAppendix a Environmental Specifications Maximum Power Consumptions Power SpecificationsQuality and Reliability CertificationsRJ-45 Twisted Pair Port Pinouts Pin MDI Signal MDI-X SignalTransmitter Fiber Optic Port SpecificationsPinout Pair GeneralReceiver Pin S1 Port S2 Port Pin SignalRJ-45 Style Serial Console Port Pinouts Stacking Port Pinouts115 Appendix a Technical Specifications 116

AT-8100S/48POE, AT-8100S/48, AT-8100L/8, AT-8100L/8POE-E, AT-8100L/8POE specifications

Allied Telesis is renowned for its range of high-performance networking solutions, and the AT-8100 series exemplifies their commitment to innovation in the network switch market. Designed for small to medium-sized businesses, the AT-8100L and AT-8100S series includes several versatile models: AT-8100L/8POE, AT-8100L/8POE-E, AT-8100L/8, AT-8100S/48, and AT-8100S/48POE. These products combine advanced features with user-friendly management tools, making them ideal for various applications.

One of the standout features of the AT-8100 series is its Power over Ethernet (PoE) capabilities, particularly in models like the AT-8100L/8POE and AT-8100S/48POE. These switches can deliver power to connected devices, such as IP cameras, wireless access points, and VoIP phones, over the same cabling that carries data. This simplifies installations and can reduce infrastructure costs, as there’s no need for additional power sources for each device.

The AT-8100L/8POE and AT-8100L/8POE-E are equipped with 8 Ethernet ports, with the PoE models supporting up to 15.4W per port on the standard. The AT-8100S/48 boasts an impressive 48 ports, making it suitable for high-density environments. All units in the series are designed to handle Layer 2 networking protocols, ensuring reliable and swift data transfer within local area networks.

Management features are robust and user-friendly. The switches support both web-based and command-line interface management, allowing network administrators to tailor their control methods according to preference and familiarity. The AT-8100 series includes features such as VLAN support, quality of service (QoS) settings for traffic prioritization, and link aggregation for increased bandwidth and redundancy.

Security is a critical aspect of modern networking, and Allied Telesis addresses this with features like port security and DHCP snooping. These functionalities help prevent unauthorized access and protect the network from various types of attacks.

In summary, the Allied Telesis AT-8100 series switches, including the AT-8100L/8POE, AT-8100L/8POE-E, AT-8100L/8, AT-8100S/48, and AT-8100S/48POE, provide a blend of PoE capabilities, robust management features, and solid performance. Their reliability and ease of use make them an excellent choice for businesses looking to enhance their network infrastructure. As organizations increasingly rely on connected devices, the AT-8100 series equips them with the necessary tools to build efficient and secure networks.
Top Page Image Contents