Allied Telesis AT-FS709FC manual Gone of these switch ports, use a cross-over cable

Page 29

AT-FS709FC Series Installation Guide

4.Power ON the switch by connecting the power cord to the AC power connector on the back panel of the switch and by connecting the power cord to an appropriate AC power source.

The PWR LED on the switch’s front panel should be ON. If the LED remains OFF, refer to “Verifying and Troubleshooting the Installation” on page 20 for assistance.

Warning

The power cord is used as a disconnection device. To de-energize

equipment, disconnect the power cord.

9

5. Connect the twisted pair cables to the RJ￿-45 connectors on the switch. When cabling the ports, observe the following guidelines:

Ports 1X through 7X are configured as MDI-X. When connecting a device with an MDI port to one of these ports, use straight-through twisted pair cabling. When connecting a device with an MDI-X port to

Gone of these switch ports, use a cross-over cable.

You do not need to use a cross-over cable to connect a device to Port 8. If the end node has an MDI port, connect the device to Port 8MDI-X on the switch. If the end node has an MDI-X port, connect it to Port 8MDI.

Note

You can use either Port 8MDI or Port 8MDI-X on the AT-FS709FC Ethernet switch. You cannot use both ports simultaneously.

6. Remove the dust cover from the fiber optic port and connect the fiber optic cable to the port. When cabling the port, observe the following guidelines:

Make sure that the cable connected to the fiber optic receiver port on the switch is connected to the transmitter port on the remote end node and that the fiber optic transmitter port on the switch is connected to

Gthe receiver port on the end node.

The fiber optic port on the network device that you connect to the AT-FS709FC Series Ethernet switch must have the same operating characteristics as the fiber optic port on the switch. For example, the maximum operating distance and operating wavelength of the end node’s fiber optic port should be the same as the switch’s fiber optic port. For technical specifications on the fiber optic port on the switch, refer to “Technical Specifications” on page 21.

19

Page 28 Page 30
Image 29
Page 28 Page 30
Contents AT-FS709FC Page Federal Communications Commission Electrical Safety and Emission Compliance StatementWanneer u de Table of Contents Appendix C Welcome to Allied Telesyn Where to Find Web-based Guides Document ConventionsOnline Support Telephone and Fax Support Contacting Allied TelesynMail Support Returning ProductsTell Us What You Think FTP Server For Sales or Corporate InformationOverview Features of the switch includeIllustrates the AT-FS709FC Series Fast Ethernet Switch Duplex Mode Type of Connector10/100 Mbps Twisted Pair Ports SpeedPort 8MDI and Port 8MDI-X Ports 1X to 7X MDI-X ConfigurationMaximum Distance Mbps Fiber Optic Port Maximum Distance MAC Address Table Introduction to Ethernet SwitchingStore and Forward Flow Control LED System LEDsNetwork Topologies FS709FC PowerCollapsed Backbone Hub Topology Collapsed Backbone Switch Topology Page Reviewing Safety Guidelines Installing the SwitchVerifying the Package Contents Twisted Pair Cable and Fiber Optic Cable Guidelines Selecting a Site for the SwitchInstalling a Rack-mounting Bracket Installing the SwitchGone of these switch ports, use a cross-over cable Verifying and Troubleshooting the Installation Physical Specifications Warranty Registration Technical SpecificationsEnvironmental Specifications Translated Electrical Safety Emission Information Radiated Energy Declaration of ConformityLightning Danger Electrical NoticesGefahr Durch Blitzschlag VorsichtFare Under Uvejr Elektriske Forholdsregler Advarsel Risiko for Elektrisk StødGevaar Voor Blikseminslag Salamaniskuvaara Sähköön Liittyviä Huomautuksia Varoitus SähköiskuvaaraPericolo DI Fulmini Avvertenze ElettricheElektrisitet Fare for LynnedslagPerigo DE Choque Causado POR Raio Peligro DE Rayos Avisos ElectricosTillkännagivanden Beträffande Elektricitetsrisk Fara FÖR BlixtnedslagPage Incident Summary Technical Support Fax OrderPage Allied Telesyn International, Corp AT-FS709FC Installation Guide Feedback
Top Page Image Contents