3Com 3C172203, 3C17204 manual Initial Switch Setup Methods, Manual Setup Automatic Setup

Page 30

30CHAPTER 3: SETTING UP FOR MANAGEMENT

Preparing for Once your Switch’s initial set up is complete you can set up your chosen Management management method as described in “Methods of Managing a Switch”

on page 39.

For detailed information about the specific web interface operations and command line interface commands and problem solving, refer to the “SuperStack 3 Switch Management Interface Reference Guide” on the CD-ROM that is supplied with the Switch.

Initial Switch Setup Before you begin the initial setup of your Switch, you must first determine your preferred setup method. There are two setup methods:

■Manual Setup — You have two choices of how to configure the IP information, as shown in Table 9.

■Automatic Setup — Your Switch must be online, that is, connected to a network. You have two choices of how to view the allocated IP information, as shown in Table 9.

Table 9 Initial Switch Setup Methods

Manual Setup

Automatic Setup

 

 

 

 

Connecting to a front panel

Use the web interface to

Using 3Com Network

Use 3Com Network

port

manually enter IP

Supervisor

Supervisor to detect the

 

information by accessing

 

automatically allocated IP

 

the Switch using its default

 

information.

 

IP address

 

 

 

169.254.100.100.

 

 

 

 

 

 

Connecting to the console

Use the command line

Connecting to the console

Use the command line

port

interface to manually enter

port

interface to view the

 

IP information.

 

automatically allocated IP

 

 

 

information.

 

 

 

 

Page 29 Page 31
Image 30
Page 29 Page 31
Contents SuperStack 3C17203 3C172043Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Setting UP for Management Setting Up Command Line Interface ManagementPIN -OUTS Switch PortOnline Technical Services World Wide Web Site Null Modem Cable PC-AT Serial Cable RJ-45 Pin AssignmentsPage About this Guide Text Conventions ConventionsList conventions that are used throughout this guide Icon DescriptionRelated DocumentationComments ProductRegistration Documentation Pddtechpubscomments@3com.comIntroducing Hardware Features Switch Hardware featuresSoftware features Four groups supported Statistics, History, AlarmsEvent Switch Front View DetailColor Indicates Port Status LEDs Module Packet LEDsModule Status LEDs Power/Self Test LED Color IndicatesUnit LEDs To your Switch. Contact your supplier for more information Switch 4400 Rear Switch 4400 rear viewView Detail Default Settings shows the default settings for the Switch Installing the Switch Package Contents Rack-mounting Placing Units On Top of Each OtherStacking Units Switch Power-upPowering-up SequencePower/Self Test LED colors Color StateCross-over Cable Straight-through Cable Installing the Switch Setting UP for Management Manual IP Configuration Setting UpIP Configuration OverviewAutomatic IP Configuration Initial Switch Setup Methods Manual Setup Automatic SetupPanel Port Manual SetupConnecting the Workstation to the Switch Pre-requisitesConfiguring the Workstation with IP Information Setting Up the Switch with IP InformationConnecting a workstation to the Switch via the console port Setting Up the Switch with IP Information Manual Setup Documentation supplied with the terminal emulation software Automatic Setup Example top-level command line interface menu Viewing IP Information via the Console PortRefer to Setting Up Command Line Interface Management on CLI management via the console portRefer to Setting Up Web Interface Management on Refer to Setting Up Snmp Management onInterface Management Command LineNetwork Using Telnet CLI Management viaChoosing a Browser Setting Up WebInterface Over the NetworkManagement workstation Setting Up SnmpManagement Protocol Snmp can manage a Switch if Documentation supplied with the Snmp network managementYou can change the default passwords using either User Default Access Level Name PasswordSecurity Device User Modify operation on the web interface Problem Solving For Technical Support information, see Appendix DPower LED does not light Solving ProblemsSolutions below On powering-up, the Power/Self Test LED lights yellowUnit LED is flashing green ProblemsSolving Hardware An Snmp fan fail trap is receivedSolving Communication Problems IP AddressingHow do you obtain a registered IP Address? Problem Solving Safety Information Important Safety Information This must be approved for the country where it is used’information de Sécurité Importante Schko Wichtige Sicherheitsinformationen Vorsicht Europe PC-AT Serial Cable Null Modem Cable 9-pin to RS-232 25-pinPin to 9-pin RJ-45 Pin ConnectorsModem Cable AssignmentsPin Number Signal Function Appendix B PIN-OUTS Switch 4400 24-port Switch 4400 24-port Technical SpecificationsProtocols Used for Administration Standards SupportedTerminal Emulation Switch 4400 48-port Switch 4400 48-port Technical SpecificationsAppendix C Technical Specifications Services Online TechnicalUsername anonymous Asia, Pacific Rim Europe and South AfricaCountry Telephone Number Fax Number NET 3Com 408 326 800 638 Not toll-free Enterprise Customers Appendix D Technical Support Index NumbersUnit information label Regulatory Notices

3C17204, 3C172203 specifications

The 3Com 3C172203 and 3C17204 are part of the 3Com series of networking products that have made significant contributions to local area networks (LANs) and enterprise connectivity. While they may not be as widely recognized today as newer technologies, their features, technologies, and characteristics played an essential role in enhancing network performance and reliability during their peak usage.

One of the defining features of the 3Com 3C172203 and 3C17204 is their support for Ethernet networking, which was pivotal in establishing fast and reliable communication between devices on a network. These products typically supported both 10Base-T and 100Base-TX standards, providing a flexible transition from older networks to faster Ethernet speeds. This backward compatibility ensured that organizations could upgrade their networks incrementally without needing a complete overhaul, thereby preserving their existing investments in infrastructure.

Both models also supported features designed to optimize network performance and provide enhanced management capabilities. For instance, built-in diagnostic features enabled network administrators to troubleshoot connection issues more effectively, thereby reducing downtime. Additionally, these devices incorporated intelligent switching capabilities that could manage data flow efficiently, prioritizing traffic and optimizing available bandwidth to ensure a smooth user experience, even under heavy load.

In terms of physical design, the 3C172203 and 3C17204 were built with a focus on durability. These units often featured robust metal enclosures suitable for various environments, from office spaces to more demanding industrial settings. Furthermore, their compact design allowed for easy integration into existing network setups without requiring significant rack space, making them an attractive option for enterprises looking to maximize their networking capabilities.

Security features were also a consideration in the design of these networking devices. They implemented basic security protocols to safeguard the integrity of data transmitted across the network, ensuring that unauthorized access was minimized and overall network security was enhanced.

In conclusion, the 3Com 3C172203 and 3C17204 represent an era of networking technology characterized by their support for Ethernet standards, intelligent switching capabilities, robust design, and essential management features. These products were integral in facilitating the growth of LANs and laid the groundwork for the advanced networking solutions that followed in the years ahead. While newer technologies have emerged since then, the fundamental principles established by devices like the 3C172203 and 3C17204 continue to influence contemporary networking designs.
Top Page Image Contents