General Installation Procedure, Wood | Maxxsonics TXi15080, TXi7508

GENERAL INSTALLATION PROCEDURE

System Design

The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link.

Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion. Lower power amplifiers will clip earlier than their more powerful cousins, and cause loudspeaker failure when overdriven, due to the harmonics generated by a clipped signal, thus overheating voice coils.

Amplifiers should be mounted with the fins running horizontally for best convection cooling, to minimize overheating. Purchase the best quality RCA cables you can afford, for reliability and less engine noise interference in the audio system.

Installation

WOOD

It is highly recommended that the amplifier be mounted to a board of MDF or other solid structure using the 4 mounting screws provided. Avoid mounting the

amplifier to metal as this can introduce noise and other unwanted issues. When mounting the amplifier, ensure that it is mounted HORIZONTALLY, as shown in the diagram above, for optimal heat dissipation. Mounting amplifiers to speaker enclosures is not recommended as this can cause damage to the amplifier components. When choosing a location for mounting the amplifier, ensure that you check for clearance from wires, gas tank, electrical devices and brake lines etc.

General:

Run the wiring so that RCA cables are at least 18“ away from power and speaker cables. Keep RCA cables away from electrical devices in the vehicle that can cause electrical noise, such as electric fuel pumps, emission control modules and other on-board electronic modules.

Power and ground connections(see the features matrix on page 9 for proper gauge cables per amplifier):

Use a sufficient gauge power cable and ground cable using the chart below as reference to what size wire you require. Titan series amplifiers require 4 gauge power wire. In a multi amplifier system, add the total value of the manufacture recommended fusing to get your total system amperage. Some applications may require multiple runs of power wire to meet the system requirements. In multi amplifier systems it is advisable to mount a large enough fuse right at the battery, and run one or multiple +12 volt power cables to a fused distribution block near the amplifiers. It is then a simple matter to connect the +12 volt terminal of each amplifier to the distribution block. During this process, please ensure that the main power fuse is removed to avoid shorting the electrical system. The main fuse must be within 12” of the vehicles battery.

Ground each amplifier with as short a ground lead as possible directly to the vehicle chassis using 4 gauge wire or equivalent to the size of the amplifiers’ power wire. Use a ground distribution block, if you wish, but it is extremely important to keep the main ground lead from this distribution block to the chassis as short as possible , not more than 12“. The ground connection integrity to the chassis is very important, and the best way to achieve a good, solid electrical and mechanical contact is to use a large round crimp lug, crimped and soldered to the ground cable. The next step is to scrape the paint off the vehicle chassis , slightly larger than the ground lug, at the connection point. Drill a clearance hole in the chassis, the same size as the lug hole, and use a bolt, spring washer and nut to securely fasten the ground lug. Use petroleum jelly to coat the bolt/lug connection, to prevent oxidization with time.

TIP: Use the same approach when installing head units, equalizers or any audio equipment for that matter - run short individual grounds from each piece directly to the vehicle chassis, to minimize ground loops and system noise. All power, ground and speaker connections should be crimped and soldered for reliability. Make sure that none of the cable insulation can chafe against exposed metal in the vehicle, causing short circuits to the chassis.

NOTE: This Matrix is a general rule of thumb. Please refer to the manufacturers specific requirements. Titan specifications can be found on page 9.

Safe connection sequence:

After all cables are run, connect speaker wires to the speakers and amplifiers, then run and plug in RCA cables. Next, connect all power, ground, and remote turn on leads. Now connect all +12 volt cables to the amplifier/s and distribution blocks and fuse holders. Finally, connect the main +12 volt cable to the battery, with the main fuse removed, and we are almost ready to power up the system.

Power up the system:

The following procedure may seem like overkill, but there is nothing more frustrating when turning on a system for the first time, and it does not work properly immediately.

First, make sure the head unit is off, and turn all level controls to minimum (counterclockwise), including the head unit volume control. Set all equalizers to 0 dB (no boost), and all crossover frequency controls at approximate frequencies, as recommended by the loudspeaker manufacturer. Set all input selector and crossover switches as required for the application. Remove all amplifier fuses, and insert the main fuse at the battery. If the fuse does not blow, you can insert the fuse in one of the amplifiers, and we are ready to turn on the system. Turn the head unit on, insert a CD, or select a radio station, and increase the head unit volume control. If the system sounds fine, turn off the head unit, and install fuses in the remaining amplifiers, one by one, till the complete system is powered up and functioning properly.

TXi10080, TXi6008, TXi4408, TXi15080, TXi4008 specifications

Maxxsonics is a prominent player in the audio industry, and their TXi series amplifiers exemplify the brand’s commitment to high-performance sound. The TXi15080, TXi4408, TXi4008, TXi6408, and TXi7508 are designed to deliver exceptional audio quality for car audio enthusiasts and installers alike. These amplifiers are engineered to provide powerful amplification while ensuring efficiency and flexibility in various applications.

The TXi15080 offers a robust power output, making it ideal for driving multiple speakers or subwoofers. Its high-current power supply and advanced thermal management help maintain performance even under heavy loads, while its compact design allows for easy installation in tighter spaces. With a signal-to-noise ratio that exceeds industry standards, users can expect crystal-clear sound quality.

Moving to the TXi4408, this amplifier is designed with versatility in mind. It features a four-channel configuration that allows it to power both speakers and subwoofers simultaneously. The TXi4408 incorporates a built-in crossover, giving users control over frequency distribution to enhance their sound system’s overall performance. The adjustable gain and bass boost options provide audiophiles with the flexibility to fine-tune their listening experience.

The TXi4008 follows suit with a two-channel design that focuses on delivering high-fidelity audio at lower power levels. This makes it an ideal choice for those who want to improve their factory systems without overwhelming their vehicles’ electrical systems. Its compact footprint makes it easy to install while still producing a powerful output.

For those needing more power, the TXi6408 is a six-channel amplifier that combines high power with flexibility. It includes features such as adjustable crossover settings and a built-in equalizer, which makes it an excellent option for custom audio setups. The TXi6408 is suitable for driving a full-range speaker setup, delivering deep, rich bass alongside clear highs, ensuring a balanced listening experience.

Lastly, the TXi7508 stands out with its high-performance capabilities, boasting an impressive power rating and flexibility for varied setups. Its advanced circuitry is designed to provide greater stability and efficiency, mitigating any risk of distortion even at high volumes. Like its counterparts, the TXi7508 offers extensive configurability, allowing users to adapt their sound systems to their specific needs.

In summary, the Maxxsonics TXi series amplifiers are characterized by their robust power outputs, adaptability to different audio configurations, and user-friendly features that make them an excellent choice for both beginner and seasoned audio enthusiasts. Each model encapsulates the essence of high-quality sound and efficiency, catering to the diverse needs of modern car audio systems.