Rosewill RNX-N600UBE user manual 2400.0-2483.5 MHz, Country, Restriction, Reason/remark

Page 2

Wireless N Dual Band Adapter RNX-N600UBE

User Manual

 

 

 

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference.

2)This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National Restrictions

2400.0-2483.5 MHz

Country

Restriction

Reason/remark

 

 

 

Bulgaria

 

General authorization required for outdoor use and public

 

service

 

 

 

 

 

France

Outdoor use limited to 10 mW

Military Radiolocation use. Refarming of the 2.4 GHz band

EIRP. within the band 2454-2483.5

has been ongoing in recent years to allow current relaxed

 

MHz

regulation. Full implementation planned 2012

Italy

 

If used outside of own premises, general authorization is

 

required

 

 

 

 

 

Luxembourg

 

General authorization required for network and service

 

supply(not for spectrum)

 

 

 

 

 

Norway

Implemented

This subsection does not apply for the geographical area

 

within a radius of 20 km from the centre of Ny-Ålesund

 

 

 

 

 

Russian

 

Only for indoor applications

Federation

 

 

 

 

 

 

Note: Please don’t use the product outdoors in France.

2

Image 2
Contents Wireless N Dual Band Adapter RNX-N600UBE User ManualCountry Wireless N Dual Band Adapter RNX-N600UBE2400.0-2483.5 MHz RestrictionTable of Content Chapter 1 Overview 1.1 Package Content1.3 Features 1.2 Overview of the ProductDimension 1.4 Product SpecificationOutput Power OS supportStatus 1.5 System Requirement1.6 LED Status Working StatusChapter 2 Installation Guide 2.1 Hardware InstallationPlease insert the CD into your CD-rom drive Click on the “Driver 2.2 Installing Drivers and/or UtilityInstallation” option when the Smart Wizard page popup Click Yes if the following window popup driver and Ralink WLAN Utility” or “Install Driver only” Once select, please click “Next ” to continue “Ralink Configuration Tool” or “Microsoft Zero Configuration Tool”Please select “Install” to continue Setup wizard will process Click “Finish” to complete the installation processWin7 Win XPChapter 3 Wireless Connection Guide 3.1 Connecting with Microsoft Zero Configuration tool Win XP3.2 Connecting with Window Select your desired SSID, then Click “Connect” 3.3 Connecting with Ralink Wireless Utility This is the startup window of the Ralink Wireless Utility Site Survey Link Information Profile Advanced About4.1 Station Mode Chapter 4 Ralink Utility ConfigurationLaunch Config Utility 4.1.1 Site Survey‹ Profile to jump to profile list window ‹ Rescan to update and refresh surrounding wireless networks4.1.1.1 Connect Once you highlighted the desired SSID, then clickmanually, otherwise, you can just click for next step 4.1.2 Profile 4.1.2.1 Add / Edit Profile ‹ Network Type4.1.2.2 Add WPS Profile 4.1.3 Link Information ‹ Link Status ‹ Throughput ‹ Statistics Statistics displays the detail counter information4.1.4 Advanced ‹Advanced4.1.5 About ‹ Certification Management4.2 AP Mode 4.2.1 Window‹ AP button will be added to menu bar of main window 4.2.1.1 ConfigurationNote ASCII characters include any numbers/letters and characters ‹ MAC Table 4.2.1.2 Switching to Working Station Mode‹ AP Configuration 4.2.2 Windows 2000 / XP / Vista Right-click the tray icon and select switch to AP Mode4.2.2.1 Config AP ‹ SSID Enter a name of SSID for Soft AP 4.2.2.2 Advanced be able to reach your RNX-N600UBE 4.2.2.3 Access Control List 4.2.2.4 Associate ListClick Associate List button from menu bar, below window will pop out Page there may be a problem with the broadband connection 5. Nothing happens when I click ‘Open Config Utility’ 7. The network is slow / having problem when transferring large files
Related manuals
Manual 15 pages 21.32 Kb