Pico Communications PicoScope 2104, PicoScope 2105 manual Safety warning, FCC notice

Page 4

2

PicoScope 2104 & 2105 PC Oscilloscope User Guide

1.3Safety warning

We strongly recommend that you read the general safety information below before using your PicoScope PC Oscilloscope for the first time. Safety protection built in to the equipment may cease to function if the equipment is used incorrectly. This could cause damage to your computer, or lead to injury to yourself and others.

Maximum input range

The PicoScope 2104 and 2105 PC oscilloscopes are designed to measure voltages in the range -20 V to +20 V and are protected against continuous or transient overvoltages of up to ±50 V. Any voltages in excess of ±50 V may cause permanent damage to the oscilloscope or to your computer.

Measurement category

PicoScope 2000 Series PC Oscilloscopes are rated for use in measurement category I (EN61010 CAT I), which covers measurements on circuits not connected to the mains. You must not use your PicoScope PC Oscilloscope to make measurements on any circuit directly connected to the mains, unless you use a purpose-built isolating probe rated for the appropriate voltage and measurement category.

Safety grounding

The PicoScope PC Oscilloscopes connect directly to the ground of a computer through the interconnecting cable provided.

As with most oscilloscopes, avoid connecting the ground input to any source other than ground. If in doubt, use a meter to check that there is no significant AC or DC voltage between the ground input of the oscilloscope and the point to which you intend to connect it. Failure to check may cause damage to your computer, or lead to injury to yourself and others.

You should assume that the product does not have a protective safety earth.

Repairs

PicoScope PC Oscilloscopes contain no user-serviceable parts. Repair or calibration of the unit requires specialised test equipment and must be performed only by Pico Technology. Spare probe tips are available from Pico Technology and its authorised distributors.

1.4FCC notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

For safety and maintenance information see the safety warning.

PS2100044-1.0

Copyright 2006 Pico Technology Limited. All rights reserved.

Image 4
Contents PicoScope 2104 Table of Contents Safety symbols IntroductionOverview IntroductionSafety warning FCC noticeCE notice Licence conditionsWarranty TrademarksCompany details AddressProduct information Minimum system requirementsInstallation instructions Checking the installationInput connector Connectors and controlsSpecifications Technical reference Driver error codesDriver 1 ps2000closeunit Functions2 ps2000flashled 3 ps2000gettimebase 4 ps2000gettimesandvalues 5 ps2000getunitinfo Information returned Example6 ps2000getvalues 7 ps2000lastbuttonpress8 ps2000openunit 9 ps2000readyPs2000runblock 11 ps2000runstreaming Ps2000setchannel Code Enumeration Range13 ps2000setets Ps2000settrigger 15 ps2000stopMore on block mode Advanced featuresSampling modes More on streaming mode TriggeringETS Equivalent Time Sampling Voltage ranges7 AC/DC operation OversamplingScaling Reading VoltageCombining oscilloscopes Using different modes Using block modeUsing streaming mode Using ETS modeProgramming 1 CGUI example Console exampleVisual Basic DelphiExcel Agilent VEETroubleshooting Software error codesGlossary Real-time continuous mode Streaming modeGlossary PicoScope software TimebaseIndex ETSIndex USBInterworld Electronics & Computers Inc