TDK blu2i Electrical and radio characteristics, Absolute Maximum ratings, Operating temperatures

Page 16

5Electrical and radio characteristics

5.1 Absolute Maximum ratings

Absolute maximum ratings for supply voltage and voltages on digital and analog pins of the module are listed below. Exceeding these values will cause permanent damage.

 

Minimum

Maximum

Peak current of power supply

0mA

100mA

Voltage at digital pins

-0.3V

3.7V

Voltage at POWER pin

3.3V

7V

5.2 Operating temperatures

 

Minimum

Typical

Maximum

Operating temperature

-20°C

25°C

+75°C

5.3 Power Consumption

The current drain from the Vcc power input line is dependent on various factors. The three most significant factors are the voltage level at Vcc, UART baud rate and the operating mode.

The hardware specification for the blu2i module allows for a voltage range of 3.6 to 6.0v at Vcc. Tests have shown that there is no significant difference in current draw when Vcc is 5 or 6V. Therefore the data presented below, pertains to Vcc levels of 3.6 and 5v only. Tests have shown that where power drain is an issue, it is best to keep Vcc at the lower end of the range.

The UART baud rate has a bearing on power drain because as is normal for digital electronics, the power requirements increase linearly with increasing clocking frequencies. Hence higher baud rates result in a higher current drain.

Finally with regards to operating mode the significant modes are; idle, waiting for a connection, inquiring, initiating a connection and connected. With connected mode, it is also relevant to differentiate between no data

16 of 36

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Blu2i Module User Guide Contents Before You Begin Safety GuidelinesRF Approvals Feature Implementation FunctionsApplication Interface Serial InterfacePower Supply Details the power consumption in different modesBlu2i Module Parallel PIO Port SPI BusPCM Codec Interface Electrical specification of the interface Pin Signal DescriptionPage Electric Characteristics Function Signal Name Pin No Signal level CommentsUSB D Physical Characteristics Mechanical DimensionsMounting the blu2i Module onto the application platform Board to Board ConnectorPart number Stacking height HRS number Parameter Specification 40 pin Board to Board connector Electrical and radio characteristics Operating temperaturesPower Consumption Absolute Maximum ratingsATD Baud rate 9600 38400 115200 460800 Low Power Modes using Sniff High Power Consumption RF performance 5.5.1Transmit Power 2Receive Sensitivity4Performance against Temperature Reliability Parameter Minimum MaximumDirection Connector Pin Label Function RS232 Modem SignalsDirection Function Modem signalling over Bluetooth Break signal on RX lineReset Pure Cable Replacement Mode Data CableATS512=3 ATS0=-1 Audio CableATS512=1 Modem Control and Status Signals ATS504=1 ATS530=2000 ATS532=1ATS0=1 Getting StartedATDbdaddr AT+BTP Factory Default Mode SoftwareBaud rate 300 to Parity Europe EU Declaration of Conformity Appendix aFCC and Industry Canada Statements ESD Electrostatic Discharge Appendix BAdditional Statement Warranty

blu2i specifications

The TDK Blu2i is an innovative Bluetooth audio device designed to elevate the listening experience for audiophiles and casual listeners alike. This versatile device combines advanced Bluetooth technology with high-quality audio performance to create an outstanding solution for wireless sound.

One of the standout features of the TDK Blu2i is its compatibility with various Bluetooth profiles, allowing it to seamlessly connect with a wide range of devices, including smartphones, tablets, and laptops. Utilizing the latest Bluetooth 5.0 technology, the Blu2i ensures a stable connection, reduced latency, and an extended range, making it ideal for both indoor and outdoor use.

In terms of audio performance, the TDK Blu2i boasts impressive sound quality. The device supports high-resolution audio streaming, delivering superior clarity and detail. Users can enjoy their favorite tracks with deep bass, crisp highs, and an overall balanced sound profile. The built-in digital signal processing (DSP) enhances audio playback, ensuring that every note is rendered with precision.

Another notable characteristic is the TDK Blu2i's long-lasting battery life. With up to 20 hours of playback on a single charge, users can indulge in extended listening sessions without worrying about frequent recharging. The device also features quick charge capability, allowing users to enjoy several hours of playback with just a short charging session.

The design of the TDK Blu2i is both stylish and functional. Its compact and lightweight form factor makes it easy to carry, while its durable construction ensures it can withstand everyday use. The device is equipped with intuitive controls, allowing users to adjust volume, skip tracks, and manage calls effortlessly.

Additionally, the TDK Blu2i supports voice assistant integration, enabling users to access their smart devices hands-free. This feature adds an extra layer of convenience, allowing for seamless multitasking without the need to reach for a phone.

In summary, the TDK Blu2i is a powerful Bluetooth audio device that encapsulates the essence of modern audio technology. With its high-quality sound, extensive battery life, and user-friendly features, it caters to the needs of any audio enthusiast looking for a reliable and high-performing wireless solution.
Top Page Image Contents