Quantum DLT-S4 quick start Connecting the Tape Drive, Connecting the Scsi

Page 2

DLT-S4 Tape Drive Quick Start Guide

The tape drive performs a self-diagnostic test, called a

4 Terminate the SCSI bus by connecting a SCSI terminator

Power-On Self-Test (POST), each time you power it on.

to the tape drive’s upper SCSI connector. See figure 3.

3 During POST, each LED lights in sequence. When POST

 

has completed successfully, the middle LED stops

Figure 3 Connecting the SCSI

flashing and remains illuminated and the left and right

Cable (Single Tape Drive)

LEDs remain off.

 

NOTE: The DLT-S4 tape drive is equipped with a soft-load

 

mechanism that automatically loads tape cartridges

 

into the tape drive. This mechanism is “parked” prior

 

to first power-on. Upon first power-on, the soft-load

 

mechanism becomes “un-parked” and ready for use.

 

When moving or shipping the unit, you must “park”

 

the soft-load mechanism. For instructions, see the

 

DLT-S4 Product Manual.

 

4 Power off the tape drive and disconnect the power cord

5 Verify that the tape drive communicates properly with

from the AC outlet.

the host computer before adding more SCSI devices to

 

the SCSI bus (see Confirming the Installation).

 

6 Add SCSI devices in a daisy chain by removing the SCSI

Connecting the Tape Drive

terminator and connecting the tape drive’s upper

connector to the next SCSI device (see figure 4).

To connect the tape drive:

7 Terminate the last SCSI device in the daisy chain by

connecting a terminator to the SCSI device’s next

 

1 Make sure the tape drive and host computer are

unused SCSI connector.

powered off.

CAUTION: You must terminate the SCSI bus by

2 Each SCSI device attached to the SCSI bus must have a

connecting a terminator to the last SCSI device in

unique SCSI ID. The tape drive’s pre-set SCSI ID is 3. If

the chain.

necessary, change the SCSI ID using the SCSI ID switch

 

on the rear of the tape drive. See figure 2.

 

CAUTION: Do not use SCSI ID 7 — this ID is in use by the SCSI card.

Figure 4 Connecting the SCSI

Cables (Daisy Chain)

Terminator

Figure 2 Setting the SCSI ID

Terminator

3Connect the tape drive’s lower SCSI connector to the host computer. Make sure the connector is firmly seated.

2

Image 2
Contents Getting Started DLT-S4 Tape DriveQuick Start Guide Checking the Tape DriveConnecting the Tape Drive Connecting the ScsiConfirming the Installation Performing a Trial BackupZum Einstieg DLT-S4-BandlaufwerkKurzanleitung Bandlaufwerk überprüfenÜberprüfung der Installation Anschluss des BandlaufwerksÜberprüfung der Installation Versuchs-Backup durchführenPara comenzar Unidad de cinta DLT-S4Manual de referencia Comprobación de la unidad de cintaConexión de la unidad de cinta Figura 1 Comprobación de la unidad de cintaConfirmación de la instalación De pruebaMise en route Lecteur de bande DLT-S4Guide de démarrage rapide Contrôle du lecteur de bandeLinstallation Connexion du lecteur de bandeValidation de linstallation Exécution dun essai de sauvegardeはじめに テープ ドライブのチェックテープ ドライブの接続 設置の確認 バックアップ テスト시작하기 테이프 드라이브 확인테이프 드라이브 연결 설치 확인 시험 백업 수행DLT-S4 磁带机 正在验证磁带机连接磁带机 正在确认安装正在执行试用备份软件 81-81283-03 A01

DLT-S4 specifications

The Quantum DLT-S4 is a breakthrough in data storage technology that revolutionizes the way organizations handle and secure data. Combining advanced features with high-capacity storage capabilities, the DLT-S4 is designed to meet the demands of modern data management while ensuring reliability and efficiency.

One of the key characteristics of the Quantum DLT-S4 is its impressive storage capacity. It supports a native capacity of up to 800 GB, with the ability to reach 1.6 TB when using compression. This makes it an ideal choice for organizations handling vast amounts of data, such as archiving, backup, and big data applications. The DLT-S4 easily accommodates growing data needs while maintaining optimal performance.

The technology behind the DLT-S4 leverages a high-density, helical-scan recording scheme, which enhances data transfer rates and integrity. With a native transfer rate of 24 MB/s, the DLT-S4 ensures rapid data access and retrieval, significantly reducing backup and restore times. This efficient performance is critical in environments where time-sensitive data management is essential.

Furthermore, the design of the Quantum DLT-S4 includes features that promote data security and longevity. It employs advanced error correction algorithms that enhance data reliability, minimizing the risk of data loss due to corruption or hardware failure. The inclusion of robust encryption methods ensures that sensitive information remains protected, a crucial requirement in today's data-centric world.

Compatibility is another strength of the DLT-S4. It is designed to work seamlessly with a variety of backup and archiving software solutions, making it flexible enough to fit into diverse IT environments. Additionally, the DLT-S4 is backwards compatible with previous DLT technologies, allowing organizations to leverage existing investments while upgrading their storage capabilities.

Efficiency is also a significant factor in the DLT-S4's design. Its energy-efficient operation reduces power consumption, thus benefiting organizations both economically and environmentally. With a manageable physical footprint, the device is easy to integrate into any data center setup.

In conclusion, the Quantum DLT-S4 stands out due to its impressive capacity, advanced recording technology, robust security features, broad compatibility, and energy efficiency. It is a reliable solution for organizations looking to enhance their data storage capabilities while ensuring data integrity and security. Its forward-thinking design and performance attributes make it a compelling choice for enterprises ready to tackle the challenges of contemporary data management.