SUPER MICRO Computer P8SC8, P8SCI I/O Port/Control Panel Connector Locations, Front Control Panel

Page 27

Chapter 2: Installation

2-5 I/O Port/Control Panel Connector Locations

The I/O ports are color coded in conformance with the PC99 specification to make setting up your system easier. See Figure 2-3 below for the colors and locations of the various IO ports.

Figure 2-3. I/O Port Locations and Definitions

Parallel Port (Burgundy)

Mouse (Green)

Keyboard

USB 0/1 Ports

COM1 Port

GLAN1

GLAN2

VGA Port

 

(Purple)

 

(Turquoise)

 

 

 

 

 

 

Front Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 2-4 for the pin definitions of the various connectors including the speaker. Refer to Section 2-6 for details.

20 19

Ground

X

Power On LED

IDE/SATA LED NIC1 LED

NIC2 LED

Overheat/Fan Fail LED

X

Ground

3V Standby

2 1

NMI

X

Vcc

Vcc

Vcc

Vcc

Vcc

X

Reset Reset Button

Signal Power Button

2-7

Image 27
Contents Super Page Manual Organization About This ManualTable of Contents Table of Contents TroubleshootingAppendices BiosIntroduction Running Setup Main Bios Setup Security BootOverview ChecklistAsia-Pacific Contacting SupermicroHeadquarters EuropeP8SC8 Image Motherboard Layout M p e r s Description Default Setting Connectors DescriptionP8SC8/P8SCi Quick Reference Intel E7221 Copper River Chipset System Block Diagram Motherboard Features Expansion SlotsPC Health Monitoring Other Acpi FeaturesDimensions Onboard I/OGraphics Memory Controller Hub Gmch Intel ICH6R System FeaturesGraphics Features/Display Chipset OverviewCPU Thermal Management PC Health MonitoringPower Configuration Settings Wake-On-Ring WOR Header Power SupplySuper I/O P8SC8/P8SCi User’s Manual Unpacking PrecautionsInstallation Procedures Static-Sensitive DevicesInstallation of the LGA775 Processor LGA775 Processor and Heatsink Fan InstallationPage CPU Installation of the HeatsinkHeatsink Removal Mounting the Motherboard in the ChassisUse your thumbs Installing DDR2 MemoryMemory Module Installation See Figure SupportFront Control Panel I/O Port/Control Panel Connector LocationsATX PWR Connecting CablesPower Supply Connectors Pwon ConnectorReset Connector OH/Fan Fail LED Reset PWR-OnOverheat/FanFail LED IDE/SATA LED NIC2 LED NIC1 LED NIC1/NIC2 LED IndicatorsNMI Power OnLED ConnectorNMI Button PWR-On LEDSpeaker Speaker ConnectorSerial Ports COM1Fan 2 Fan Fan HeadersChassis Intrusion FanUSB 2/3 USB 6/7 ATX PS/2 Keyboard and PS/2 Mouse PortsUniversal Serial Bus USB KB/Mouse USB 0/1WOL Wake-On-RingWake-On-LAN WORVGA Connector Giga-bit LAN Ethernet PortsSMB Header PWR LED Sata LED Power LEDClear Jumper SettingsExplanation Jumpers Cmos ClearUSB Wake-Up Keyboard Wake-UpJWAKE1 Gigabit LAN Enable GLAN1 EnableGLAN2 Enable Force PWR- On Force-Power-On Enable/ DisableScsi Enable/Disable *P8SC8 only Scsi EnableWatch Dog Jumper Settings JWD Watch Dog Enable/DisableGLAN1 Onboard IndicatorsGlan LEDs LeftRightPrinter Parallel Port ConnectorIDE Floppy ConnectorIDE Connector FloppyScsi Channel a Connectors *P8SC8 onlyUltra320 Scsi Scsi Channel BNo Video Troubleshooting ProceduresBefore Power On No PowerTechnical Support Procedures Memory ErrorsLosing the System’s Setup Configuration Frequently Asked Questions Question How do I update my BIOS?Question What type of memory does my motherboard support? Question Whats on the CD that came with my motherboard? Other connectors to your hard drives. Consult the docuQuestion What are the function keys for the IPMIVIEW? Returning Merchandise for ServicePage Introduction System BiosHow To Change the Configuration Data Starting the Setup UtilityRunning Setup Main Bios SetupPress DEL to enter Setup Swap Floppy Drive Main Bios Setup MenuDate/Time Legacy Diskette A/Legacy Diskette BHalt On Access ModeIDE HDD Auto-Detection IDE Channel 0 to IDE Channel 3 MasterAdvanced Bios Features Advanced Bios SetupWatch Dog Timer Select Quick BootQuiet Boot Apic ModeOn-Chip Frame Buffer Size Dram Data Integrity ModeSata Mode Advanced Chipset ControlUSB 2.0 Controller Pata IDE ModeSata Port USB ControllerRxD, TxD Active Uart Mode SelectIR Transmission Delay UR2 Duplex ModeECP Mode Use DMA Use IR PinsParallel Port Mode EPP Mode SelectIRQ Resources Reset Configuration DataInitial Display From Resources Controlled ByXpci Express Root Port Function Onboard LAN Boot ROMPCI-E Compliance Mode Hardware MonitorsSystem Temperature CPU Warning TemperatureProcessor & Clock Options DMI Event Log Agent Connect Via Console RedirectionConsole Redirection Baud RateSecurity Set Supervisor PasswordSet User Password Password CheckBoot First Boot DeviceSecond Boot Device Boot Other Device Third Boot DeviceExit Appendix a Bios Post Messages Page Appendix B Award Bios Post Codes Post hex Description Appendix B Award Bios Post Codes P8SC8/P8SCi User’s Manual Appendix B Award Bios Post Codes P8SC8/P8SCi User’s Manual ATA Operation Modes Configuring Intel ICH6R Sata RAID FunctionSerial ATA Sata Introduction to Intel ICH6R SerialRAIDSata Operate Modes BiosCreating, Deleting and Reseting RAID Volumes Using Intel ICH6R Sata RAID Utility ProgramPage Page Deleting RAID Volume Reset Disks to Non-RAID New Operating System-Windows XP/2000 Installation Exiting the ICH6R Sata RAID Configuration Utility ProgramEach item, you must re-boot the system before moving on to Installing Intel Application Accelerator UtilityPage Appendix C Software Installation Page Installing the Operating System and other Software Programs Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control