Xantech 680-10 installation instructions Mounting, 480-00

12-20-00 Rev.C

ZONE 4
490-00 Series
Micro Link™
IR Receivers
3-Wire
Cable	Red
	Stripe
+12V	IR OUT
GND

ZONE 3

480-00

Dinky Link™

IR Receiver

3-Wire

Cable

Red Stripe

+12V IR OUT

GND

ZONE 2

+12V	J-BOX RECEIVER	780-10
	+12 VDC
IR OUT	IR OUT
GND	GND
	+12V	IR OUT

780-10

J-Box

IR Receiver

Smart

Pad™

GND

ZONE 1

291-10

Hidden Link™

IR Receiver

7 Foot Quick

Connect Cable

Do not use

these jacks X X

OUT PWR

CB12
Connecting	IR RCVR
Block
	V G	S

3-Conductor Cable (unshielded OK)

795-20FOUR ZONE AMPLIFIED CONNECTING BLOCK

795-20

Four Zone

COMMON

ZONE

IR ZONE

Amplified

ZONE 1

ZONE 2 ZONE 3

ZONE 4

Connecting

+12 IN G +12 IN G +12 IN G +12 IN G

Block

ZONE 4

ZONE 3

ZONE 2

ZONE 1

POWER

10

9

8

7

6

5

4

3

2

1

A

B

A

B

A

B

A

B

+12V

120 V AC

(unswitched)

Satellite Receiver		To Zone 4		To Zone 3		To Zone 2	To Zone 1
		Emitter			Emitter	Emitter	Emitter
VCR	Emitter
						To 120 V AC
		680-10				(Unswitched)		Zone 1	AV Receiver Zone 1
							782-00
	Emitter	Remote AC						Emitter
Laser Disc		Switcher					Power Supply
			120 VAC 15A MAX	➧RESET
	Emitter						Zone 1 AC		AV Receiver Zone 2
CD Changer		5AMAX	OUTLET4		5AMAX	OUTLET1		Zone 2
								Emitter
Cassette DecK	Emitter						Zone 2 AC		AV Receiver Zone 3
								Zone 3
				TOTAL				Emitter
COMMON		5AMAX	OUTLET5		5AMAX	OUTLET2			AV Receiver Zone 4
	283M Blink-IR™			LOADLIMITEDTO			Zone 3 AC	Zone 4
	Mouse Emitters
SOURCES	AC for			15A				Emitter
	"Power Line Switchable"
	Common Sources

786-00

Unregulated

Power Supplies plugged into an AC outlet on each Zone Receiver

–

+

–

+

–

+

White striped side –

AC

Power

Strip

OUTLET 6 5A MAX		5A MAX	OUTLET 3
TEMPORARY POWER TAP CAUTION: TO REDUCE THE RISK USE INDOORS IN A DRY LOCATION.	REMOTE AC SWITCHER	680-10
OF
ELECTRIC SHOCK		CONFIRM	IR
		INPUT

Zone 4 AC			ZONE
		RECEIVERS
				599-00
590-00	To 120 V AC			Pulsed
	(unswitched)		786-00	Switching
				Module
Programmable Controller			Power Supply
(back view)

																RES DEL SEQ PGM
+																	12VDC		1 2 3 4
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	O G			BANK
																	–	+

12VDC

–

+

IN+ IN– GND +12V

MODULE	599-00PULSED SWITCHING
GND +12V	OFF ON

MAIN ROOM, EQUIPMENT CABINET, ETC.

Fig. 3 A typical application of the 680-10 for AC switching in a 4-zone system.

6.The common source components that can remember their ON condition when their power cords are unplugged, are all powered from the #6 outlet on the 680-10. Those that cannot, such as the VCR and the Satellite Receiver shown in Fig. 3, must be plugged into unswitched outlets and receive their IR power commands from the 590 through the 795 and the common emitters.

7.The common sources are therefore switched ON when the first AV receiver is turned ON, and will remain on until the last AV receiver is turned OFF.

8.Finally, ON and OFF IR commands from the RC68+, for outlets #1 through #4, are "taught" into a learning remote, such as a Xantech URC-1, and into the Xantech Smart Pad, along with all other desired system commands, for total system operation.

9.To embellish the system further, you could add the GP-ONand GP-OFFcommands from the RC68+ programmer to the keypads or the URC-1 remotes so that all zones may be turned ON or OFF from any zone location.

See the 795-20 Installation Instructions for additional information regarding zoned systems

MOUNTING

The 680-10 has four attached rubber feet for stand-alone mounting. Underwriters Laboratories defines the 680-10 to be a moveable device and therefore it is not to be fastened down permanently to any surface. It may however, be placed in any orientation to accommodate the installation.

4 

680-10