Important Safety Instructions

VEC1026BD_Manual_050305 5/9/05 2:25 PM Page ii

WARNINGS

1.RISK OF EXPLOSIVE GAS MIXTURES — WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.

2.To reduce risk of battery explosion, follow these instructions and those published by the battery manufacturer and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary markings on these products and on engine.

3.This equipment employs parts (switches, relays, etc.) that produce arcs or sparks. Therefore, if used in a garage or enclosed area, the unit MUST be placed not less than 18 inches above the floor.

Battery Safety

1.When working with lead acid batteries, always make sure immediate assistance is available in case of accident or emergency.

2.Always use protective eyewear when using this product: contact with battery acid may cause blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact with battery acid.

3.There is a risk of releasing explosive gases when lead acid batteries are charged or discharged. Failure to follow instructions may cause property damage and/or personal injury.

4.When connecting the battery clamps to a discharged battery and an alarm sounds — the clamp connections are incorrect and need to be reversed.

5.Jump-start procedures should only be performed in a safe, dry, well-ventilated area.

6.Always store battery clamps detached from unit when not in use. Never touch battery clamps together. This can cause dangerous sparks, power arcing and/or explosion.

7.When using this unit close to the vehicle’s battery and engine, stand the unit on a flat, stable surface, and be sure to keep all clamps, cords, clothing and body parts away from moving vehicle parts.

8.Do not wear vinyl clothing when jump-starting a vehicle, friction can cause dangerous static- electrical sparks. Remove all jewelry or metal objects that could cause short circuits or react with battery acid.

9.Never allow RED and BLACK clamps to touch each other or another common metal conductor — this could cause damage to the unit and/or create a sparking/explosion hazard.

10.a. For negative-grounded systems, connect the POSITIVE (RED) clamp to the POSITIVE ungrounded battery post and the NEGATIVE (BLACK) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.

b.For positive-grounded systems, connect the NEGATIVE (BLACK) clamp to the NEGATIVE ungrounded battery post and the POSITIVE (RED) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.

11.Always disconnect the NEGATIVE (BLACK) jumper cable first, followed by the POSITIVE (RED) jumper cable, except for positive grounded systems.

12.Do not expose battery to fire or intense heat since it may explode. Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).

13.Do not smoke or use flammable items (matches, cigarette lighters, etc.) while working on a vehicle’s battery system.

14.Whether stored or in use, keep this unit out of reach of children.

15.Do not operate charger in rain or snow, nor use when wet.

16.DO NOT ATTEMPT TO JUMP-START A FROZEN BATTERY.

17.When using an extension cord, make sure it has the same configuration as the plug of the unit and the cord is properly wired and in good electrical condition. This cord needs to be suitable for 120 volt AC and have a minimum 2 amp rating.

18.Place this unit as far away from the battery as DC cables permit.

19.Never allow battery acid to come in contact with this unit.

20.Do not operate this unit in a closed area or restrict ventilation in any way.

Personal Safety

FIRST AID

SKIN: If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap and water. If redness, pain, or irritation occurs, seek immediate medical attention.

EYES: If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seek immediate medical attention.

IMPORTANT

This unit is delivered in a partially charged state. Fully charge unit with the supplied 120 volt AC charger for a full 40 hours before using for the first time. You cannot overcharge the unit using the AC charger method.

1.Use a common household extension cord for charging (not supplied).

2.Do not recharge for more than 3-4 hours maximum using the 12 volt DC method. Recharge unit after each use.

3.All ON/OFF switches should be in the OFF position when the unit is charging or not in use. Make sure all switches are in the OFF position before connection to a power source or load.

4.Never insert anything other than the supplied power/recharging cords or recommended appliance power/recharging cords into the 12 volt DC charging/power outlet on this unit. Do not use any accessory that is not recommended or provided by the manufacturer.

5.Do not use this unit to operate appliances that need more than 5 amps to operate from the 12 volt DC accessory outlet.

6.This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect to a 6 volt or 24 volt battery system.

7.This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a vehicle that does not have a battery installed.

8.Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump- started. Before jump-starting, read the vehicle’s owners manual to confirm that external-starting assistance is suitable.

9.Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after the recommended number of attempts, discontinue jump-start procedures and look for other problems that may need to be corrected.

10.Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during storage, use and recharging. To avoid possible damage that may shorten the unit’s working life, protect it from direct sunlight, direct heat and/or moisture.

11.Check unit periodically for wear and tear. Take to a qualified technician for replacement of worn or defective parts immediately.

12.NEVER submerge this unit in water.

SAVE THESE INSTRUCTIONS

iii

250, BD050205, VEC1026BD specifications

The Vector VEC1026BD is a high-performance vehicle engine diagnostic tool designed to streamline the process of identifying and resolving vehicle issues. It addresses the ever-evolving complexities of modern vehicle electronics, offering technicians a comprehensive solution equipped with advanced technologies and features.

One of the main features of the VEC1026BD is its compatibility with a wide range of vehicle makes and models, including domestic and foreign brands. This versatility ensures that users can rely on the tool for a variety of tasks, whether they are working on passenger cars, light trucks, or heavier vehicles. The device is particularly valued for its extensive database of trouble codes, which serves as a reference for technicians when diagnosing problems.

Another key feature is the device's user-friendly interface. The VEC1026BD comes with a large, high-resolution display that clearly presents data, making it easy for users to navigate through menus and access functions. The intuitive design minimizes the learning curve for new users while also providing experienced technicians with quick access to complex diagnostic tools.

Incorporating advanced connectivity options, the VEC1026BD offers Bluetooth and Wi-Fi capabilities, allowing for seamless communication with other devices. This facilitates real-time data sharing and remote diagnostics, enabling technicians to collaborate effectively with colleagues and customers. Furthermore, software updates can be easily downloaded, ensuring that users always have the latest diagnostic capabilities and vehicle information at their fingertips.

The VEC1026BD also emphasizes efficiency with its fast data processing speeds. Its powerful internal processor enables rapid retrieval and analysis of vehicle data, accelerating the diagnostic process. This means less time spent troubleshooting and more time dedicated to repairs, ultimately improving shop productivity and customer satisfaction.

In terms of build quality, the VEC1026BD is designed for durability in demanding environments. The rugged casing protects the device from drops and impacts, making it suitable for everyday use in workshops and garages. Additionally, the tool is equipped with a long-lasting battery, ensuring that technicians can complete their tasks without frequent interruptions for recharging.

Overall, the Vector VEC1026BD stands out as a reliable diagnostic tool that combines advanced technology, user-friendly features, and robust construction. Its wide compatibility, efficient operation, and connectivity options make it a valuable asset for automotive professionals seeking to enhance their diagnostic capabilities and deliver effective service to their clients.