Document Only Reference | Plantronics DYNZ-600 Series specification

F-23371

Electronic Speed Switch Technical Manual

Page 5

6.3.3Adjust the signal generator frequency to the desired SW1 set/trip point as specified or calculated in step 6.2.1.

6.3.4Slowly turn the SW1 setpoint potentiometer adjustment counterclockwise until the ohmmeter indicates an open circuit. This gives you the correct setpoint for SW1.

6.3.5Slowly increase the signal generator frequency until the ohmmeter connected to terminals 10 to 12 indicates an open circuit. Note the frequency and verify that it is correct for your SW1 set/trip point requirements. If set/trip point of SW1 is correct it is properly calibrated. If set/trip point is incorrect, go to step 6.2.3, 6.3.3 and 6.3.4 and calibrate unit.

7.1.2Check input signal from MPU on terminals 5 and 6 with an AC voltmeter — must be greater than 0.7 volts rms.

7.1.3Check wiring to speed switch.

7.2 TRIPPING AT WRONG RPM

7.2.1Check for proper trip point settings.

7.2.2See calibration section.

7.3RELAY DOES NOT FUNCTION 7.3.1 Check wiring to relays.

6.4CALIBRATION OR CHECKING PROCEDURE FOR OS-SW2 TRIP POINT

6.4.1 With no power applied to unit, connect an ohmmeter to terminals 7 and 9 (no other wires attached). The ohmmeter should indicate zero resistance (short circuit). This is the normally closed contact on relay OS-SW2.

6.4.2 Apply correct DC power to terminals 1 and 2 of speed switch. The ohmmeter should indicate zero

	Uncontrolled
resistance (short circuit) with the signal generator
frequency set below the OS-SW2 set/trip point;
therefore, it must not change states when power is
applied.

NOTE

If you are only checking calibration point, omit steps 6.4.3 and 6.4.4 and go to step 6.4.5.

6.4.3 Adjust the signal generat r frequency to the

desired OSSW2 set/trip point as specif ed or calculated in step 6.2.1.

6.4.4	Slowly turn the OS-SW2 potentiometer
counterclockwise until the ohmmeter indicates an
open	istorical
open	circuit. This gives you the correct setpoint for
	H

6.4.5Slowly increaseForthe signal generator frequency until the ohmmeter connected to terminals 7 to 9 indicates zero resistance. Note the frequency and verify that it is correct for your OS-SW2 set/trip point

requirements. If set/trip point of OS-SW2 is correct, it is properly calibrated. If set/trip point is incorrect, go toOS-SW2.

step 6.2.3, 6.4.3 and 6.4.4 and calibrate unit.

7.3.2Check relay contacts for proper operation.

Document Only

Reference

– CAUTION –

As a safety measure, the engine should be equipped with an independent overspeed

shutdown device in the event of failure which

may render the governor inoperative.

7.0 TROUBLESHOOTING PROCEDURE

The unit is potted and, therefore, non-repairable, but the following checkpoints can be used to determine if there is an internal fault.

7.1 UNIT DOES NOT FUNCTION

7.1.1Check battery voltage on terminals 1 and 2. DYNZ-60010-000-0-40 — 8 to 40 Vdc DYNZ-60012-000-0-74 — 58 to 88 Vdc DYNZ-60013-000-0-40 — 8 to 40 Vdc

- NOTE -

Barber-Colman believes that all information provided herein is correct and reliable but reserves the right to update at any time. Barber- Colman does not assume any responsibility for its use unless otherwise expressly undertaken.

DYNZ-600 Series specifications

The Plantronics DYNZ-600 Series represents a hallmark of innovation in the realm of professional communication headsets. Designed to meet the dynamic needs of modern workplaces, this series combines advanced technologies with user-focused features, making it ideal for both office and remote work environments.

At the heart of the DYNZ-600 Series is its exceptional audio quality, which is achieved through high-definition wideband audio. This ensures crystal-clear voice transmission, enabling users to engage in conversations without misunderstanding or the distraction of background noise. The headset also incorporates noise-canceling microphone technology, effectively filtering out ambient sounds and enhancing the clarity of voice communication. With this feature, professionals can focus on their discussions without the interference of surroundings.

Comfort is a cornerstone of the DYNZ-600 Series design. The headsets come equipped with lightweight materials and plush ear cushions, allowing users to wear them for extended periods without discomfort. The adjustable headband and flexible microphone boom further enhance the ergonomic design, ensuring a tailored fit for each user.

Another standout characteristic of the DYNZ-600 Series is its versatility in connectivity. These headsets are engineered to seamlessly connect with multiple devices, including computers, smartphones, and tablets. The inclusion of Bluetooth technology provides wireless freedom, allowing users to move around their workspace without being tethered by cables. This is particularly beneficial in busy office environments where mobility is key.

Furthermore, the DYNZ-600 Series boasts impressive battery life, offering hours of talk time on a single charge. This ensures that professionals remain connected throughout their workday without the need for frequent recharging. Additionally, a quick charge feature allows users to gain several hours of use from just a short charging session, catering to the fast-paced nature of today's work environments.

In terms of design, the DYNZ-600 Series is sleek and modern, available in various styles to suit individual preferences. With options for both over-the-ear and on-ear configurations, users can select the style that best fits their personal and professional needs.

In summary, the Plantronics DYNZ-600 Series delivers a powerful combination of superior audio quality, user-friendly features, and connectivity options that cater to the evolving requirements of today's workplaces. This series stands out as an essential tool for professionals seeking reliability, comfort, and efficiency in their communication.