Clarion CZ109 To change sound settings, Setting the Z-Enhancer Plus, Adjusting the bass

Sound Adjustment

Sound effects and tone can be adjusted as desired.

To change sound settings

1.Press the [SOUND] button to switch to the sound adjustment display.

∗The factory default sound setting is “Z- EHCR+”.

2.Press [x] or [v] to select the sound

adjustment mode.

Each time [x] or [v] is pressed, the sound adjustment mode changes as follows:

“Z-EHCR+” ↔ “BASS” ↔ “TREBLE” ↔ “BALANCE” ↔ “FADER” ↔ “NF VOL”

∗When “ENT” is flashing in the display, press the [ ] button to adjust the setting value.

∗The sound adjustment mode is displayed for 2 seconds before showing the sound setting.

3.Turn the [ROTARY] knob to adjust the selected audio mode.

4.After completing settings, press the

[SOUND] button to return to the previous mode.

●Setting the Z-Enhancer Plus

This unit has 4 sound tone effects stored in memory.

Select the effect you prefer.

∗The factory default setting is “OFF”.

2-1. Select “Z-EHCR+”.

3-1. When you turn the [ROTARY] knob, the tone effect changes as follows:

“OFF” ↔ “B-BOOST” ↔ “IMPACT” ↔ “EXCITE” ↔ “CUSTOM”

OFF : No sound effect

B-BOOST : Enhanced bass

IMPACT : Enhanced bass and treble

EXCITE : Enhanced bass, mid, and treble

CUSTOM : User customized

When set to “B-BOOST/IMPACT/EXCITE”:

3-2. Press the [ ] button.

3-3. Turn the [ROTARY] knob to adjust the setting (Setting range: –3 to +3).

∗The factory default setting is “0”.

3-4. Press the [ ] button to return to the previous mode.

When set to “CUSTOM”:

3-2. Press and hold the [ ] button (1 sec.). Bass/treble characteristics become flat and “FLAT” is show in the display.

3-3. Turn the [ROTARY] knob to change to the “OFF” mode.

●Adjusting the bass

This adjustment is supported only when Z-Enhancer Plus is set to “CUSTOM”.

2-1. Select “BASS”.

3-1.	Press the [		] button.
3-2.	Press [x]	or [v] to change and select

settings as follows:

“B<G 0>” ↔ “B<F 60>” ↔ “Q 1”

3-3. Turn the [ROTARY] knob to adjust values for gain, F (center frequency) and Q curve.

B<G 0> :The factory default setting is “0”. (Adjustment range: +7 to –7)

B<F 60> :The factory default setting is “60”.

(Adjustment range: 60/80/100/200)

Q 1 :The factory default setting is “1”. (Adjustment range: 1/1.25/1.5/2)

3-4. Press the [ ] button to return to the previous mode.

●Adjusting the treble

This adjustment is supported only when Z-Enhancer Plus is set to “CUSTOM”.

2-1. Select “TREBLE”.

3-1.	Press the [		] button.
3-2.	Press [x]	or [v] to change and select

settings as follows:

“T<G 0>” ↔ “T<F 10K>”

3-3. Turn the [ROTARY] knob to adjust values for gain and F (center frequency).

T<G 0> : The factory default setting is “0”. (Adjustment range: +7 to –7)

T<F 10K>: The factory default setting is “10K”.

(Adjustment range: 10K/12.5K/ 15K/17.5K)

3-4. Press the [ ] button to return to the previous mode.

English

CZ1099