Omega Speaker Systems wi Series manual Safety Considerations, EMC Considerations

Page 7

PART 1

INTRODUCTION

1.1 Safety Considerations

This device is marked with the international caution symbol. It is important to read this manual before installing or commissioning this device as it contains important information relating to Safety and EMC (Electromagnetic Compatibility).

This instrument is a panel mount device protected in accordance with EN 61010-1:2001, electrical safety requirements for electrical equipment for measurement, control and laboratory. Installation of this instrument should be done by qualified personnel. In order to ensure safe operation, the following instructions should be followed.

This instrument has no power-on switch. An external switch or circuit- breaker shall be included in the building installation as a disconnecting device. It shall be marked to indicate this function, and it shall be in close proximity to the equipment within easy reach of the operator. The switch or circuit-breaker shall meet the relevant requirements of IEC 947–1 and IEC 947-3 (International Electrotechnical Commission). The switch shall not be incorporated in the main supply cord.

Furthermore, to provide protection against excessive energy being drawn from the main supply in case of a fault in the equipment, an overcurrent protection device shall be installed.

• Do not exceed voltage rating on the label located on the top of the instrument housing.

• Always disconnect power before changing signal and power connections.

• Do not use this instrument on a work bench without its case for safety reasons.

• Do not operate this instrument in flammable or explosive atmospheres.

• Do not expose this instrument to rain or moisture.

• Unit mounting should allow for adequate ventilation to ensure

instrument does not exceed operating temperature rating.

• Use electrical wires with adequate size to handle mechanical strain and power requirements. Install without exposing bare wire outside the connector to minimize electrical shock hazards.

EMC Considerations

• Whenever EMC is an issue, always use shielded cables.

• Never run signal and power wires in the same conduit.

• Use signal wire connections with twisted-pair cables.

• Install Ferrite Bead(s) on signal wires close to the instrument if EMC problems persist.

Failure to follow all instructions and warnings may result in injury!

1

Image 7
Contents User’sGuide Page Table of Contents List of Figures 13a List of Tables EMC Considerations Safety ConsiderationsManuals, Software Customer ServiceBefore You Begin Inspecting Your ShipmentDescription Computer Front Panel Enunciators Physical Characteristics and Mounting 2.1.1 Front PanelRear Panel Rear Panel ConnectorNetwork Mounting Dimensions DimensionsPanel Mounting Assembly and Mounting 2.1.4.1 Panel Mounting InstructionAntenna Mounting Antenna Mounting InstructionAccessing the Main Board Assembly Disassembly InstructionElectrical Installation Power Connections Mechanical Relay and SSR Wiring OutputsOutputs Wiring Hookup Pulse and AnalogFast Blow Typical Applications10 Location of S1 Jumper Jumper Settings for Display Color Setup11 Location of DIP Switches Dip SwitchesPin Name Description Network Communication Interfaces 1 10Base-T RJ-45 PinoutNetwork Protocols .1 Label Detail Ethernet MAC AddressDhcp DNS 4 Position DIP SwitchIP Address Default IP AddressSection Changing TCP/IP Properties on Your ComputerPinging the Meter from MS-DOS Prompt Testing the ConnectionIConnect Software Assigning an IP Address using iConnectAccessing the Wireless System for Configuration Access Control Setting a New IP Address over the NetworkWireless System Home Page Menu Meter’s Configurations and OperationsPower Up Meter Login and Administrator PasswordsLab Get Readings from the End DevicePage Java 1.5.x.x. Screen Shots Java Runtime Environment SetupJava 1.4.2.x Screen Shot Java Runtime Environment 1.4 Setup InstructionsAccessing Meter units over Peer-to-Peer network Accessing Meter units within your internal networkAccessing Meter units using the internet DiagnosticsGrant codeBase http//192.168.1.200 Java PolicyDjava.security.policy=C\0JAVAPOLICY\javapolicy.txt 11 Java Policy12 Chart ChartChart 13a Controller Setup Controller SetupController Setup Miscellaneous SetupTransmit Power MonitorInput SetupSetpoints & On/Off Control Setpoints & On/Off Control 15b Setpoints & On/Off Control if Analog Output Option 16 Loop Break Loop BreakAlarms 1 Alarm Analog Output Retransmission Setup19a Display Menu Display19b Display Menu if Analog Output Option Example Display Color ExamplesRED Green 20 ID Code Passcode IDTerminal Server Network SetupRemote Access Tunneling GeneralGeneral Remote AccessTerminal Server 22 End Device Setup End Device SetupEnd Device Setup Sensor1 End Device ParametersSensor2 Sensor End Device Parameters Device Name Name of this End DeviceT75F T74F Cancel UpdateDisplay Access Control List of Commands 01 indicates End Device #1 Telnet SetupCommand Description Response HTTPget Program HTTPget using PortHttpget -r -S 00000000 192.168.1.2001 where Next run HTTPget with the options displayed belowHttpget -r -S *SR00z 192.168.1.1352000 -C1 -q Arp -s 192.168.1.200 00-03-34-00-06-b6ARP Protocol 27 ARP Commands and Responses28 iLog Software Logging Data for End Device #2, 6 ILog SoftwareMail Notifier Software InstallationEmail Setup Email Address SetupMail Notifier Commands Device Setting and ConfigurationAlarm Editor General Deployment Guidelines Environment / Operating ConditionsTransmitting and receiving antenna exist Electromagnetic waves, hence the signal becomes weakerPerformance as well Distance feet With Line-of-SightSee .1.4.2 and Figure Material Type Possible SignalWithout Line-of-Sight Casing and Closure Around the AntennaNmrr 60 dB Cmrr 120 dB Digital Filter Programmable Alarm 1 & 2 programmableRelays/SSR to Relay/SSR Outputs 2300 Vac per 1 min. test Power to OutputLine Voltage/Power Low Voltage/Power OptionNetwork Topology Star Topology Range Interface SpecificationsInput Factory Preset ValuesSetpoints & On/Off Control Passcode ID Factory Preset ValuesAlarm Loop BreakMisc Factory Preset Values Analog Output RetransmissionRemote Access Tunneling Access ControlEnd Device # 1 Factory Preset Values End Device SetupAppendix Aglossary Appendix BIP Address Address Class Mask Binary Value Mask Decimal Value Ascii Dec Hex Ctrl Key Ascii Control Codes Appendix E ILog Error Messages Error # Description Page Page Page WARRANTY/DISCLAIMER PH/CONDUCTIVITY Shop on line at omega.com

wi Series specifications

The Omega Speaker Systems wi Series represents a remarkable leap in audio technology, designed for those who seek exceptional sound quality coupled with stylish aesthetics. Engineered for both audiophiles and casual listeners, the wi Series delivers a listening experience that is nothing short of extraordinary.

One of the key features of the Omega wi Series is its advanced driver technology. Each speaker utilizes custom-designed woofers and tweeters that provide a balanced frequency response across the spectrum. This ensures that lows are rich and full, while highs are crisp and clear. The integration of these components allows the wi Series to reproduce music with impressive accuracy, making it suitable for any genre, from classical symphonies to modern electronic music.

Additionally, the wi Series incorporates a unique bass enhancement technology that optimizes low-frequency performance without overwhelming the overall sound. This innovation allows listeners to enjoy deep, resonant bass lines while maintaining vocal clarity and instrumental separation. The result is a well-rounded listening experience that captures the nuances of any audio source.

The design of the wi Series is both contemporary and functional. Available in various finishes, the speakers can seamlessly blend into various home environments, from minimalist to traditional decor. The sleek cabinet design minimizes resonance and distortion, enhancing audio clarity. The series also provides versatile placement options, featuring integrated wall mounts for those who prefer a clean visual aesthetic.

Connectivity options are abundant in the wi Series. These speakers support wired and wireless connections, including Bluetooth and Wi-Fi streaming capabilities. This flexibility allows users to connect their devices effortlessly, ensuring that music can be enjoyed from any source, whether it be a smartphone, tablet, or home theater system.

Moreover, the wi Series is built with durable materials that ensure longevity. The robust construction guarantees that the speakers will maintain their performance standards over time, even in diverse environmental conditions.

In conclusion, the Omega Speaker Systems wi Series combines innovative technology, stylish design, and exceptional sound quality. With its advanced driver technology, bass enhancement features, versatile connectivity options, and durable construction, the wi Series represents a compelling choice for anyone serious about enhancing their audio experience. Whether for intimate gatherings or larger events, the Omega wi Series stands out as an investment in superior sound.