FlexPointTM 10FL/2 User Instructions
Description:
The FlexPointTM family of converters supports the IEEE 802.3 and Ethernet Versions 1.0 / 2.0 standards. They convert among
The FlexPoint 10FL/2 converts from
connector. The following models are described here:
Model | Fiber Type | Maximum Distance |
4310 | 850 nm (multimode) | 2 km |
4311 | 1310 nm | 30 km |
4312 | 1310 nm (multimode) | 5 km |
For metal ST fiber connector, add M before the ‘dash’ in the Model Number. Example:
The 10FL/2 provides a
Note that the total length of the coax cable must not exceed 185 meters and the number of stations on the coax segment must not exceed 30 stations (per IEEE 802.3 specification).
Warning
The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by Omnitron Systems Technology, Inc.
Caution
All
Warranty
This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment. TO REGISTER, COMPLETE AND MAIL OR FAX THE REGISTRATION PORTION OF THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS. During the warranty period, Omnitron will, at its option, repair or replace a product which is proven to be defective.
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense. Omnitron will pay the shipping charge to return the
Power Adapter Notice:
1.When using in a
2.This product should always be used only with Omnitron Supplied Power Unit model number
WARNING!
Before installing and connecting the Power Adapter verify that the power on the unit is appropriate for your AC line voltage source.
Mounting:
The Omnitron FlexPoint 10FL/2 can be
When connecting the FlexPoint 10FL/2 at the end of a coax segment, attach the coax cable directly into the FlexPoint’s BNC coax connector. When connecting it along the coax line (not at the end), use a “T” connector to tap into the cable.
Attach the fiber cables to the FlexPoint’s connectors. The FlexPoint’s transmit (Tx) must attach to the receive side on the device at the far end of the fiber and the receive (Rx) must attach to the transmit side.
product to Buyer’s designated US address using Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance of the equipment by Buyer,
No other warranty is expressed or implied. Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any legal theory.
Switch Settings:
“Termination” Switch: When attaching anywhere along a coax cable except at the end, the Termination Switch should be set to “Termination Out” (factory setting). When attaching to the end of a cable, it can be set to “Termination In.” Note that when the switch is set to “Termination In,” an external termination element must not be attached.
LED Indicators:
LED | Color | Description |
Power On | Yellow | Power applied |
Jabber | Red | Jabber condition |
Fiber Link | Green | Operational device detected at |
|
| the far end of fiber. |
Fiber Rx | Green | Received data on fiber line. |
Coax Rx | Green | Received data on coax line. |
Collision | Yellow | Collision detected |
Technical Support:
If you encounter problems in installing or maintaining this product, contact Omnitron Technical Support:
Phone: | (949) |
Fax: | (949) |
Address: Omnitron Systems Technology, Inc. | |
| 140 Technology Drive, #500 |
| Irvine, CA 92618 USA |
URL: | |
Notes:
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
_____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
User Warranty Registration complete both sides and mail or fax this registration form to: | Omnitron Systems Technology, Inc. 140 Technology Drive, #500 Irvine, CA 92618 USA |
Please |
|
User Warranty Registration sides and mail or fax this form to the address indicated on |
| 10FL/T 10FL/2 10T/2 Other_____ |
Please complete both | the other side. | FlexPoint Type: |
Fax: (949) | Name: _________________________________________________ | Company: ______________________________________________ | Adress:_________________________________________________ | ________________________________________________ | City:State: Zip Code: __________ | Country:________________________________________________ | Phone:Fax:________________________ | Please complete both sides of this form | ||
|
|
|
|
|
|
|
|
|
|
|
Model: _________________________________________________ | Serial Number:Purchase Date: ______________ | Purchased From: _________________________________________ | Address: ______________________________________________ | City:State: Zip Code: ________ | Country: _______________________________________________ | Comments and Suggestions: _______________________________ | ______________________________________________________ | ______________________________________________________ | Please complete both sides of this form |