NETGEAR READYNAS 4220, READYNAS 2120, READYNAS 3220 manual Boot Menu

Page 21

NETGEAR ReadyNAS OS 6 Rack-Mount Storage Systems

Boot Menu

Use the boot menu to restart or troubleshoot your ReadyNAS storage system. Your storage system has the following boot modes:

•Normal. Initiates a normal boot process, just like booting using the Power button.

•Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a 10-minute time-out period begins. During the 10-minute time-out period, you can choose to power off the storage system without causing any data loss, and the factory default process is canceled. If you choose not to power off the storage system, after the 10-minute time-out period, the factory default process begins.

WARNING:

The factory default reboot process resets the storage system to factory settings, erases all data, resets all defaults, and reformats the disk to X-RAID2.

Note: To start the factory default process immediately, press the Reset button during the 10-minute time-out period.

•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets some settings on your storage system, such as Internet protocol settings and the administrator password, to defaults.

•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a NETGEAR technical support representative instructs you to do so.

•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue data off a disk during a disaster recovery.

•Memory test. Performs a memory test. The pass or fail result is reported using the storage system’s LEDs. Contact a NETGEAR technical support representative to interpret memory test results.

•Test disk. Performs an offline full disk test. This process can take four hours or more, depending on the size of your disks. Any problems are reported in the system logs, which you can view using the local admin page. For more information about viewing the system logs, see the ReadyNAS OS 6 Software Manual.

To access the boot menu:

1. Power off your system.

2. Using a straightened paper clip, press and hold the Reset button.

3. Press the Power button on the front panel of the system.

ReadyNAS 3220 and 4220

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents September 2013 East Plumeria Drive San Jose, CA Netgear ReadyNAS OS 6 Rack-Mount Storage SystemsSupport Contents Maintenance Getting Started Additional Documentation Setup Location Supported Operating Systems Supported BrowsersDiskless Storage System ReadyNAS Front panel Front PanelRear panel Rear PanelStatus information Status InformationPower On Power On and Shut DownPreferred Shutdown Forced ShutdownPower State Boot MenuLED  To access the boot menuReadyNAS 3220 Following figure shows the front panel of the 3220 Disk tray handle Disk tray release latch This following figure shows the rear panel Rear Panel Status indicators Boot Menu System powers on Rack-Mount Setup Installation To install the system into a rack Netgear ReadyNAS OS 6 Rack-Mount Storage Systems Disks Disk tray Disk TrayReformat Previously Formatted Disks Supported Disks Previously Formatted Disks To migrate a volume to a diskless ReadyNAS OS 6 system Migrate a Volume To add a 3.5-inch hard disk drive HDD Add a DiskNetgear ReadyNAS OS 6 Rack-Mount Storage Systems Netgear ReadyNAS OS 6 Rack-Mount Storage Systems Netgear ReadyNAS OS 6 Rack-Mount Storage Systems Netgear ReadyNAS OS 6 Rack-Mount Storage Systems Replace a Disk Netgear ReadyNAS OS 6 Rack-Mount Storage Systems Slide the disk tray back into the drive bay of the system Netgear ReadyNAS OS 6 Rack-Mount Storage Systems Netgear ReadyNAS OS 6 Rack-Mount Storage Systems Maintenance Access the Inside of the Storage System  To access the inside of a 3220 or  To replace a fan on a Replace a FanNetgear ReadyNAS OS 6 Rack-Mount Storage Systems  To replace a fan on a 3220 or  To replace the battery of a Replace the On-board Battery To replace the battery of a 3220 or Defaults and Technical Specifications ReadyNAS OS 6 factory default settings Factory Default SettingsGeneral ReadyNAS 2120 Technical SpecificationsReadyNAS 3220 Technical Specifications ReadyNAS 4220 Technical Specifications Electrical Safety Precautions Safety WarningsGeneral Safety Precautions Rack-Mount Precautions Electrostatic Discharge ESD PrecautionsRegulatory Compliance Information Notification of ComplianceFCC Guidelines for Human Exposure
Related manuals
Manual 241 pages 17.38 Kb

READYNAS 3220, READYNAS 2120, READYNAS 4220 specifications

The NETGEAR ReadyNAS series encompasses a range of NAS (Network Attached Storage) solutions designed to provide reliable data storage, backup, and sharing options for both home and business users. Among the prominent models are the ReadyNAS 104, ReadyNAS 4220, ReadyNAS 316, ReadyNAS 716X, and ReadyNAS 312, each tailored to specific needs and use cases while delivering advanced features and technologies.

The ReadyNAS 104 is a four-bay desktop NAS that offers scalability and flexibility for home users and small businesses. Its ability to support up to 40 TB of storage using 10TB drives makes it a good choice for video streaming, file sharing, and automated backup tasks. The device is equipped with ReadyCLOUD technology, allowing users to access and manage their files easily from anywhere, via the mobile app or web portal.

Next, the ReadyNAS 4220 targets small and medium-sized businesses with its robust performance and enterprise-level features. Featuring up to 8 TB of storage in a 2-bay configuration, it employs the ReadyDR (Disaster Recovery) feature that allows for seamless offsite backups. The ReadyNAS 4220 excels in virtualization support, making it compatible with VMware and Microsoft environments, and offers built-in snapshot technology to safeguard data integrity.

The ReadyNAS 316 provides a perfect blend of power and features for users requiring advanced media management. With its six drive bays, it allows for extensive storage options and employs advanced data protection technologies such as RAID and BTRFS file system. The device's real-time transcoding capability is a standout feature, enabling smooth streaming of high-definition content to various devices without file format constraints.

The ReadyNAS 716X is designed for demanding workloads and power users. With its 6 bays and Intel Xeon processor, it is ideal for data-intensive applications, such as video production and large-scale backup solutions. This model supports 10GbE connectivity for high-speed data transfer and features dual power supplies for enhanced reliability, ensuring that users have a dependable system for mission-critical tasks.

Lastly, the ReadyNAS 312 offers a cost-effective solution for entry-level users who still need powerful performance. With 2 bays and support for up to 20 TB of storage, it utilizes the same advanced RAID technologies for data protection. The inclusion of features like real-time file syncing and play-out functionality makes it ideal for home users looking to centralize their media library and access their files anytime.

Overall, the NETGEAR ReadyNAS series presents a variety of options, each equipped with essential features and advanced technologies, catering to the diverse demands of users seeking reliable and efficient data storage solutions.
Top Page Image Contents