SB104.QCard.R2 9/7/00 4:53 PM Page 2
INSTALL THE WINDOWS 98 DRIVERS
This guide provides instructions for installing the Windows 98 network driver. Since all versions of Windows may not respond similarly, your computer screen may display different information, in a differ- ent order, than pictured in the following instructions. This procedure works for the FA311.
Note: You must install the network card (instructions on the other side of this guide) before installing the network driver.
You need to have the Windows 98
Note: If the “Insert Disk” window opens and a message prompts you to insert your disk at any time during the installation process, insert the Windows CD in Drive D (the CD drive) and click on “OK.” Then follow the next step in the instructions.
1.Turn on the power to the computer and start Windows. The new Hardware is found.
2.In the first “Add New Hardware Wizard” dialog box that indicates a PCI Ethernet Controller is found, click on “Next.”
3.Select “Search for the best driver…” Click on “Next.”
Add New Hardware Wizard
What do you want windows to do?
Search for the best driver for your device (Recommended).
Display a list of all the drivers in a specific location, so you can select the driver you want.
< B a c k | N e x t > | C a n9179DAc e l |
4.Select “Floppy disk drives” and insert the NETGEAR FA311 Fast Ethernet PCI Adapter Drivers and Diagnostics disk into the floppy drive. Click on “Next.”
5. Click on “Next” in the Update Device Driver Wizard.
6.When the “Network” window opens, enter a name (a different
7.When asked to insert the NETGEAR FA311 Fast Ethernet PCI Adapter Drivers disk, click on “OK.”
8.Type A:\ in the “Copy files from” entry field and click on “OK.” The system copies the files from the driver diskette.
9.Make sure the Windows 98
10.Make sure the designated path to the Windows 98
11.In the “Update Device Driver Wizard” dialog box, click on “Finish.”
12.Remove the NETGEAR FA311 Drivers and Diagnostics disk and the Windows 98
You must restart your computer to complete the installation of the driver.
VERIFY INSTALLATION
1.
2.
3.
4.Click on “Device Manager.”
5.
6.If there is a problem with the installation of the driver, an exclamation point appears next to
“NETGEAR FA311 Fast Ethernet PCI Adapter.” If there is an exclamation point,
INSTALL THE NETWORK SHARING SOFTWARE
1.Insert your Resource CD into the CD drive and type the following at the prompt:
RUN CD:\SETUP.EXE
where “CD” is the CD drive letter.
2.Follow the steps shown onscreen to complete the installation process. After completing installation, you can now connect to your network.
REPLACEMENT POWER ADAPTER
If, for any reason, the power adapter for any of the hubs fails, please contact NETGEAR immediately to order a replacement adapter. Use the following table when ordering a specific power adapter.
Order Code | EN104TP |
|
Power adapter (7.5 V DC, 1 A), North America | ||
Power adapter (7.5 V DC, 1 A), Europe | ||
Power adapter (7.5 V DC, 1 | A), United Kingdom | |
Power adapter (7.5 V DC, 1 | A), Australia | |
Power adapter (7.5 V DC, 1 | A), Japan | |
|
|
|
TECHNICAL SPECIFICATION
| Model FA311 Network Card | Model EN104TP Ethernet Hub |
Software | NetWare tested and approved Microsoft Windows 95, Windows 98, | |
Compatibility | Windows NT® compatible |
|
Standards | IEEE 802.3u | IEEE 802.3i |
Compatibility | Ethernet, IEEE 802.3i |
|
| Ethernet, Autosensing PCI |
|
|
| |
Network Interface | 5 | |
|
|
|
|
|
|
Power |
|
|
Power consumption | 3 W | 7.5 W |
DC operating voltage | +5V +/- 5% @ 630 mA maximum | 7.5 V @ 1 A maximum |
|
|
|
Physical Specifications |
|
|
Dimensions | 5.7 by 3.7 in. | 4.6 x 3.1 x 1.2 in. |
| 14.4 by 9.3 cm | 118 x 78 x 29 mm |
Weight | 0.20 lb (90 g) | 1.25 lb (.6 kg) |
|
|
|
Environmental |
|
|
Specifications |
|
|
Operating temperature | 0 to 40˚C |
|
Operating humidity | 10 to 90% noncondensing |
|
Agency Compliance | CE Mark, commercial, | CE Mark, commercial, |
| FCC, Part 15, Class B | FCC, Part 15, Class A |
| EN 55 022 (CISPR 22), Class B | EN 55 022 (CISPR 22), Class A |
| Canada | VCCI Class A |
Safety Approvals | CE Mark, commercial | CE Mark |
|
| UL Listed |
|
| cUL Listed |
|
| TUV licensed |
|
| |
|
|
|
Warranty Information | Limited lifetime | 5 years |
|
|
|
HARDWARE WARRANTY
Subject to the provisions described below, the components in this NETGEAR product kit are protected from defects in material and workmanship as follows:
The network cards and cables are protected by a limited lifetime warranty, the hub or switch is protected by a
Should a product fail to perform as described above within the first year following the original date of purchase, NETGEAR will ship a replacement for the failed product upon return of the defective product.
Products that fail after the first year following the original date of purchase will be repaired or replaced with the same or functionally equivalent, product by NETGEAR, at its discretion, free of charge provided you (1) have, within 30 days of the original date of purchase, completed and returned the Owner Registration Cards which accompanied the products when shipped, (2) return the failed product to NETGEAR designated repair facility with shipping charge prepaid, and (3) provide NETGEAR with proof of the original date of purchase. Repaired or replacement products will be returned to you with shipping charges prepaid.
Replacement products may be refurbished or contain refurbished materials. If NETGEAR, by its sole determination, is unable to repair or replace the defective product, it will refund the depreciated purchase price of the product.
This warranty does not apply if, in the judgement of NETGEAR, the product fails due to damage from shipment, handling, storage, accident, abuse or misuse, or if it has been used or maintained in a manner not conforming to product manual instructions, has been modified in any way, or has had any serial number removed or defaced. Repair by anyone other than NETGEAR or an approved agent will void this warranty. The maximum liability of NETGEAR under this warranty is limited to the purchase price of the product covered by the warranty.
Prior to returning any defective product, the end customer or the reseller from whom the end customer originally purchased the product must obtain a Return Materials Authorization (RMA) number from NETGEAR. All defective products should be returned to NETGEAR with shipping charges prepaid. NETGEAR will not accept collect shipments.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT OR AS REQUIRED BY LAW, THE WARRANTIES AND REMEDIES STATED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS, ORAL OR WRITTEN, EXPRESS OR IMPLIED. ANY AND ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS ARE EXPRESSLY EXCLUDED. NETGEAR SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANY PERSON FOR ANY SPECIAL, DAMAGES RESULTING FROM USE OR MALFUNCTION OF THE PRODUCTS, LOSS OF PROFITS OR REVENUES OR COSTS OF REPLACEMENT GOODS, EVEN IF NETGEAR IS INFORMED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES.