Technical Support
PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH YOUR PRODUCT.
By registering your product at www.NETGEAR.com/register, we can provide you with faster expert technical support and timely notices of product and software upgrades.
NETGEAR, INC.
Support Information
Phone:
Troubleshooting
The Power light is not lit
The switch has no power. | Power |
•Make sure the power cord is properly connected to the switch.
•Make sure the power adapter is properly connected to a functioning power outlet. If it’s in a power strip, make sure the power strip is turned on. If the socket is controlled by a light switch, make sure the switch is in the on position.
•Make sure you are using the NETGEAR power adapter supplied with your switch.
The Port number light is not lit for a connected device or stays on continuously
There’s a hardware connection problem.
•Make sure the cable connectors are securely plugged in at the switch and the device.
•Make sure the connected device is turned on.
•If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card or adapter is installed correctly and is working.
•Make sure the cable is less than 328 feet (100 meters).
Technical Specifications
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the product described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model GS105A Gigabit Ethernet Switch has been suppressed in accordance with the conditions set out in the
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
ProSafe 5 Port Gigabit Switch
10/100/1000 Mbps GS105A
©2004 NETGEAR, Inc. NETGEAR, the Netgear logo, Auto Uplink, ProSafe and Everybody's connecting are trademarks or registered trademarks of Netgear, Inc. in the United States and/or other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. All rights reserved.
2 0 1 - 1 0 8 1 7 - 0 1 | March 2006 |
|
Standards Compatibility:
Network Interface: Power:
Physical Dimensions: Weight:
Operating Temperature: Operating Humidity: Electromagnetic Compliance: Safety Agency Approvals for the Power Adapter: Performance Specifications Frame Filter Rate:
Frame Forward Rate:
Network Latency:
(using
Address Database Size:
Addressing:
Queue Buffer:
ISO/IEC 802.3i (ANSI/IEEE 802.3i)
IEEE 802.3x Flow Control; Jumbo frame 9K, IEEE 802.1p priority; DSCP priority
Compatible with Windows®, Mac® OS, NetWare®, Linux®
W:101 mm (3.9") D: 94 mm (3.7") H: 27 mm (1.1") 0.28 kg (0.621 lbs)
0 to 50° C (32 to 122° F)
10% t0 90% relative humidity, noncondensing
CE mark, Commercial; FCC Part 15, Class A; EN 55 022 (CISPR 22),
CE mark, Commercial UL listed (UL 1950),
14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port/1,488,000 frames/sec for 1000M port
14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port / 1,488,000 frames/sec max for 1000M port
100 Mbps to 100 Mbps: 20 μs max
1000 Mbps to 1000 Mbps: 10 μs max
4000 MAC addresses
128 KB Embedded
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR Model GS105A Gigabit Ethernet Switch is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a.
Conformity is declared by the application of EN 55 022 Class A (CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model GS105A Gigabit Ethernet Switch) does not exceed the Class A limits for
Department of Communications
Réglement sur le brouillage radioélectrique du ministère des Communications Cet appareil mumérique (NETGEAR Model GS105A Gigabit Ethernet Switch) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.
Installation Guide
Introduction
The NETGEAR® ProSafe
Model GS105A ProSafe
The GS105A Gigabit Ethernet Switch enables you to build a small network that gives you 10, 100, or 1000 Mbps access to other devices on the network. It provides a full, dedicated 1000 (or 100, or 10 Mbps) connection between two devices. If a device has
Ethernet cables come as either
If you have a problem with your switch, NETGEAR offers support 24 hours a day and 7 days a week on the Web (www.NETGEAR.com), by
Installation Overview
Estimated Time:
1.Unpack the box and verify the contents.
2.Prepare to install the switch.
3.Install the switch and connect the other devices.
1 Unpack the Box and Verify the Contents
Model GS105A
Gigabit Ethernet Switch
Installation guide,
warranty card andPower adapter Support information card
When you open the box, verify that you received everything. The package includes:
•ProSafe
•AC power adapter
•
•GS105A Installation Guide (this document)
•Warranty/Support information Card
If you don’t have everything listed above, see the support information card for contact infor- mation. If you’re missing the support information card itself, get contact information at www.NETGEAR.com in the Technical Support area.
2 Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface — such as a table, desk or shelf. The switch comes with
Make sure the selected location is:
•Not in direct sunlight or near a heater or heating vent.
•Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all sides of the switch.
•Well ventilated (especially if it is in a closet).
Also, you’ll need one Category 5 (Cat 5) Ethernet cable with
3Install the Switch and Connect the Other Devices
Apple G4 | PC with | Server with GA311 | DSL |
| GA311 | Adapter | modem |
| Adapter |
|
|
|
|
| LOCAL |
|
|
|
|
|
8 | 7 | 6 | 510/100M 4 | 3 | 2 | 1 | INTERNET |
|
|
|
|
|
|
|
| 12VDC 1.2A |
|
|
|
|
|
|
|
| OFF | ON |
GS105A | FVS318 ProSafe VPN Firewall |
| |
Gigabit Ethernet Switch |
|
1.Place the switch on a flat surface or hook onto the screws.
2.For each device, insert one end of an Ethernet cable into the port in the device and insert the other end into one of the Ethernet ports on the switch.
3.Connect the power adapter’s cord into the back of the switch and then plug the adapter into a power source (such as a wall socket or power strip).
The Power light |
|
| 100M | 10M | |||
Power | LED | LED | |||||
| |||||||
should light up. |
|
|
|
|
|
| |
|
|
|
|
|
| ||
The corresponding Link LED for |
|
|
|
|
|
| |
|
|
|
|
|
| ||
each connected and powered device |
|
|
|
|
|
| |
should light when connected and flash | Model GS105A | ||||||
when activity occurs.If the connection is | Gigabit Ethernet Switch |
|
|
|
| ||
10 Mbps or 100 Mbps, one of the LEDs |
|
|
|
|
|
| |
in the
Note: If any light doesn’t operate as indicated, go to the Troubleshooting section.