NETGEAR FS526T, FS750T2NA software manual System Password, Switch Menu, Switch Port Configuration

Page 18

Smart Switch Series Software Manual

The DHCP function is enabled by default. Click Static IP Address to disable the DHCP function.

Enter site-specific IP address, Subnet mask and Gateway in the appropriate boxes

Click Apply to activate the setting

System> Password Page

The password entered is encrypted on the screen and will display as a sequence of asterisks (*). The default password is ‘password’ and can be changed here.

Type the old password in the Old Password field

Type the new password in the New Password field

Re-type the new password in the Re-type New Password field

Click Apply to activate the new password

Note: The password is case sensitive and with a maximum length of 20.

Switch Menu

There are 4 options available:

Port Configuration

Statistics

VLAN

Trunking

Switch> Port Configuration Page

You can configure the status per port by clicking a port ID at the port setting menu.

ID: The port number on the switch. Click this number to configure the port.

Speed: Indicates the communication mode set for the port. The default setting for all ports is Auto-negotiation (Auto). The possible entries are Auto-negotiation (Auto), 10 Mbps half duplex (10M Half), 10 Mbps full duplex (10M Full), 100 Mbps half duplex (100M Half), 100 Mbps full duplex (100M Full), or Disable.

4-4

Web-Based Management Interface

July 2005

Image 18
Contents Smart Switch Series Software Manual Trademarks Contents Appendix C Port-Based Vlan Chapter About This Guide Why the Document was CreatedHow to Use This Document AudienceTypographical Conventions Special Message FormatsManagement Access Overview ChapterComparing Switch Management Methods Smart Switch Series Software Manual Chapter Getting Started For a Network with a Dhcp ServerSmartwizard Discovery Web Access Click Configuration Setting For a Network without a Dhcp ServerWeb Management main Smart Switch Series Software Manual Chapter Web-Based Management Interface System Switch Status System MenuSystem IP Access List System Set-upSystem Password Switch MenuSwitch Port Configuration Switch Statistics Switch Port Configuration Set speedSwitch StatisticsQ0S Switch VlanChange members Add a port to a Vlan Group Delete a Vlan Group Switch Trunking Switch Monitor Switch Advanced Jumbo FrameSwitch Advanced Spanning Tree Firmware Configuration Backup Firmware Factory ResetFirmware Menu Logout Chapter Software Upgrade Then click Firmware UpgradeSmart Switch Series Software Manual Appendix B Ieee 802.1Q Virtual Local Area Network Vlan Ieee 802.1Q VLANs ExampleSmart Switch Series Software Manual Smart Switch Series Software Manual Appendix C Port-Based Vlan Port-based VLANsExample Scenarios Appendix D Cabling Guidelines Fast Ethernet Cable GuidelinesCategory 5 Cable Specifications Category 5 CableSpecifications Category 5 Cable Requirements Twisted Pair CablesPatch Panels and Cables Figure D-2illustrates crossover twisted pair cableUsing 1000BASE-T Gigabit Ethernet over Category 5 Cable CablingRJ-45 Plug and RJ-45 Connectors Near End Cross Talk NextPatch Cables PIN Normal Assignment on Uplink Assignment on Ports 1 to Conclusion Appendix a Default Settings Table A-1 Default SettingsSmart Switch Series Software Manual Index NumericsIndex Index Index

FS526T, FS750T2NA specifications

The NETGEAR FS750T2NA and FS526T are commendable offerings in the realm of unmanaged Ethernet switches, designed to cater to both home and small business networking needs. Boasting solid performance, these switches facilitate seamless connectivity for multiple devices, making them ideal for network expansion.

The NETGEAR FS750T2NA features 48 ports, ensuring ample connections for numerous devices. It supports auto-sensing technology, allowing devices to negotiate their speed and duplex settings, optimizing network efficiency. The switch is designed with a steel housing that enhances durability, which is critical for environments where space can be cramped.

Notably, the FS750T2NA supports a non-blocking switching architecture. This means that data can flow freely across all ports without encountering bottlenecks, delivering consistent performance, which is critical when several devices are active simultaneously. Furthermore, the FS750T2NA is equipped with IEEE 802.3x flow control, which ensures that frames are not dropped during heavy traffic, maintaining data integrity.

On the other hand, the FS526T, featuring 26 ports, offers a slightly smaller footprint while retaining robust performance. This switch also includes auto-sensing technology and a metal chassis, ensuring longevity. The FS526T caters well to environments where space is a limiting factor without compromising on performance.

Both switches support the energy-efficient IEEE 802.3az standard, which reduces power consumption during low network activity. This characteristic not only lowers operational costs but also contributes to a greener IT footprint. Moreover, users benefit from plug-and-play installation, enabling quick deployment without the need for complicated configuration.

The NETGEAR switches utilize advanced design to ensure low latency, thus enhancing the overall user experience, whether it be for data transfer, video streaming, or online gaming. Furthermore, the fanless design of the FS750T2NA and FS526T ensures silent operation, making them suitable for noise-sensitive environments.

In summary, the NETGEAR FS750T2NA and FS526T are highly effective unmanaged switches that offer substantial port availability, robust performance, energy efficiency, and ease of use. These devices stand out as reliable solutions for expanding and optimizing network connectivity in both home and small business setups.