Operation, AC On Power Switch | Cary Audio Design CAD 300 specs

OPERATION ________________________________________________________

Signal input connection is made via the input jacks on the rear of the CAD 300 SEI located next to the output binding posts. The interconnect cables from the output of the preamplifier can be any convenient length your set-up requires. The choice of a high quality interconnect cable is important. Once again, your audio dealer will have the proper cables in stock for this purpose.

Your new CAD 300 SEI is ready for operation after the speaker, interconnect cables, and the tubes have been installed. Refer to the tube placement sheet at the end of this manual for proper installation.

AC On Power Switch

Simply push the AC rocker switch on the ON position. Observe that the blue LED lights and all tubes are lit (filaments).

Break-In Period

The tubes, capacitors and output transformers take approximately 100 hours of music playing to fully settle in for peak performance. The CAD 300 SEI will sound good right out of the box and will improve with use. After the first couple of hours you will notice increased depth and tighter bass. This break-in period is true with vacuum tube based audio amplifiers.

Bias Adjustment Procedures

Look to the left rear corner of the CAD 300 SEI. You will notice a slotted screwdriver adjustment control. This is the bias adjust potentiometer. Also located in line with this control is a ¼” headphone style jack. This will accept the included orange/black test cable. These two leads will hook to a DC current meter or digital multimeter.

1.Make sure the CAD 300 SEI is in the off position with all the tubes inserted into the proper sockets.

2.Plug in the two-conductor test cable into the ¼” jack. Clip the black alligator clip to the black negative lead on your multimeter. Hook the red alligator clip to the red positive lead from the multimeter.

3.Place the multimeter range selector in the DC current range. This may say 0 – 300 mA. Just make sure you are reading DC current. Never select the DV voltage position. Only the DC current scale.

4.Locate a proper flat blade screwdriver that fits the slot on the bias adjustment control.

5.With your CAD 300 SEI plugged into the house AC mains wall socket turn on the AC power switch. Immediately observe the DC current reading. The proper value will be 150 to 160 mA.

6.If the value is low, turn the bias control clockwise (right) a small amount. If the current reads higher than 160 mA. Turn the bias adjustment control counter clockwise (left).

7.After the 300 SEI has been on for about ten minutes recheck the bias and reset to 150 to 160 mA Range. This completes the bias setting. You may wish to check this setting every six months or so. Please note that the bias will vary as your AC line voltage moves up and down in your home. This is normal. The amplifier will operate in a broad range of 120 mA to 180 mA of current. The value of 150 to 160 is the ideal point.

8.Turn off your CAD 300 SEI and remove the test cable and store this cable in a convenient location in your listening room.

WARNING

MAKE SURE AMPLIFIER IS UNPLUGGED FROM AC MAINS BEFORE SERVICING.

CAD 300 specifications

Cary Audio Design's CAD 300 is an epitome of high-fidelity audio engineering, skillfully blending classic aesthetics with cutting-edge technology. Renowned for its exceptional sound quality and craftsmanship, this amplifier has garnered acclaim among audiophiles and music lovers alike.

At the heart of the CAD 300 lies its tube amplification technology, which utilizes three 300B power tubes in a push-pull configuration. This design not only enhances power output but also ensures a rich, warm sound signature that tube amplifiers are celebrated for. The CAD 300 delivers a power output of around 15 watts per channel, allowing it to drive a diverse range of loudspeakers effectively, particularly those with high sensitivity.

One of the standout features of the CAD 300 is its fully balanced design, which minimizes noise and maximizes signal integrity. This configuration enhances the amplifier's performance by reducing crosstalk and improving the overall soundstage, providing listeners with a more immersive audio experience. The inclusion of high-quality capacitors and custom-wound transformers further elevates the amplifier's performance, allowing for precise audio reproduction across the frequency spectrum.

The CAD 300 also showcases Cary Audio's commitment to thermal management and longevity. It includes a robust chassis designed to dissipate heat effectively, ensuring that the tubes operate within optimal temperatures, thus prolonging the lifespan of the components. The amplifier's vintage-inspired design features a beautiful brushed aluminum faceplate and illuminated VU meters, which not only provide functional feedback but also add a touch of elegance to any audio setup.

User-friendly features such as the integrated volume control and speaker binding posts ensure ease of use, while the availability of multiple input options caters to diverse setups and needs. The CAD 300 also supports bi-wiring, allowing advanced users to fine-tune their audio experience further.

In summary, the Cary Audio Design CAD 300 is a remarkable amplification solution that combines traditional tube technology with modern engineering marvels. Its warm sound signature, high-quality construction, and thoughtful design make it an outstanding choice for anyone seeking to elevate their audio experience. Whether used in a dedicated listening room or as part of a high-end home theater system, the CAD 300 promises to deliver dynamic and engaging sound that resonates with discerning listeners.