Bryston SP2 PREAMP owner manual Setup & Calibration of the SP2, Setting the Speaker Configuration

Page 11

SP2 PREAMP/PROCESSOR

Works .in .conjunction .with .the .backlight .and .tilt . switch .to .determine .if .backlighting .is .needed. To. .enable .or .disable .the .backlight .in .the .remote . control, .follow .this .procedure: .

. 1. Press. .CODE .button .for .5 .seconds .

. 2. LED. .will .flash .red, .then .release .button .

. 3. Type. .in .3 .digit .code .792 .= .MODE/SAVE/DTS .

. 4. .LED .will .flash .again .to .confirm To .send .discrete/hidden .Code…

. 1. .Press .CODE .button .and .release 2. .LED .will .illuminate .(Red)

3. Type. .in .3 .digit .code .(a .combination .of .mode . buttons)

4. .LED .will .flash .again .to .confirm .and .go .out.

For other hidden codes, visit the Bryston website at www.bryston.ca

SETUP & CALIBRATION OF THE SP2

NOTE: .In most operating menu modes the last segment of line 2 of the display will either show an “X” for EXIT, or an “>” (arrow) to indicate more menu items.

Choosing (highlighting) the “X” position in the display and pressing the Select button will “EXIT” back to the previous menu, or exit the menu mode entirely. If an “>” appears, continue pressing the menu navigation arrow buttons to reveal more menu options.

In the figure below, the arrow “>” indicates more menu items:

Highlight “X” to exit

may .have .one.) .

IMPORTANT: .When .using .the .Pink .Noise .genera- tor .within .the .SP2 .for .speaker .level .calibration, .the . salient .point .is .that .all .channels .measure .equal .dB. . After .pushing .the .test .button, .the .pink .noise .will . start .in .the .front .left .speaker. .Record .the .dB .level . from .this .speaker .(with .the .level .trim .value .at .0 .dB . on .the .LCD .Display .or .on .the .Video .Monitor .when . using .the .Bryston .video .switcher), .and .adjust .all . the .others .to .match .it. .It .is .not .critical .to .reach . some .specific .dB .level .(ex. .85 .dB), .it .is .more . important .that .all .channels .are .at .equal .levels. .

NOTE: .If for any reason you are not sure that you can accomplish this calibration task or have any doubts as to how it should be done, please contact your dealer or Bryston technical support BEFORE attempting this process. Most Bryston Dealers can provide this service. Please contact your dealer for their policies and procedures in this regard. .

Explanation of ‘Saved Settings per Source’ Feature

The .SP2 .will .remember .different .mode .settings .for . each .source. .Every .time .a .source .is .engaged .it .will . recall .the .following .settings: .

. ● Digital. .Status .

Listening .Mode .(Surround, .THX, .Stereo, .Mono) .

. ● Surround .Mode .

Bypass. .Status

. ● SubWoofer level

Rear Channel Levels

Back Channel Levels

Speaker Configuration

EX Control

ES Control

In .order .to .fully .enjoy .the .capabilities .of .the .SP2 . you .or .your .dealer .must .first .set-up .and .calibrate . the .SP2. .This .is .a .critical .step .in .insuring .that .all . your .loudspeakers .are .properly .designated .within . the .unit .and .that .all .levels .and .delays .are .properly . set. .

To .accomplish .this .process .the .following .tools .are . needed: .

1:Tape measure .or .other .means .of .determining . the .distance .of .each .speaker .from .the .chosen .

listening .positions. .

2: Sound. Level Meter. .This .device .insures .that . all .loudspeaker .levels .are .precisely .matched . and .set .accurately. .This .step .cannot .accurately . be .done .by .ear, .a .test .instrument .should .be . used .to .ensure .proper .calibration. .(The .Radio . Shack .Analog .SPL .meter .is .inexpensive .and . eminently .suitable .for .this .task. .Your .dealer .

. To .save .these .settings, .make .the .preferable . mode .changes .and .adjustments .per source, .then . press .the .SAVE .button .on .the .SP2 .remote .control . before .switching .to .another .input. .

NOTE 1: You. must set the speaker configuration manually for each input, within the LCD setup menu.

NOTE 2: The. Setup Test Noise mode will over- write Rear and Sub level settings for ALL inputs.

Setting the Speaker Configuration

Before .calibrating .levels .you .must .first .tell .the .SP2 . about .your .loudspeaker .configuration. .To .do .this: .

. 1: First. .enter .the .main .menu .by .pressing .on .any . one .of .the .menu .buttons .(< .- .> .or .SELECT). .

10

Image 11
Contents SP2 Important Safety Instructions Bryston Limited WarrantyTable of Contents Introduction AccessoriesSafety Power Inlet & SwitchFront Panel Controls & Indicators SP2 Front Panel Controls & IndicatorsStereo & Stereo Downmix Mode Source Select Buttons & IndicatorsDigital Mode Select Button & Indicator Surround Mode Button & IndicatorBypass Button Mode ButtonMaster Volume Control THX ButtonBalanced Outputs Unbalanced Outputs Rear Panel Input & Output ConnectionsVideo Switcher Data Port SP2 Remote ControlSource Select Buttons Setting the Speaker Configuration Setup & Calibration of the SP2Explanation of ‘Saved Settings per Source’ Feature None. .no .subwoofer .attached .to .the .system Explanation of ‘Xtra Bass’ ModeSetting the Speaker Crossover Frequency Large vs Small Speaker SettingsFeet .to .every .speaker, .resulting .in .zero Setting the Channel DelaysCalibrating and Setting Levels/Channel to Channel Balance Setting Channel Levels without Pink NoiseEnabling DTS-ES 6.1 Decoding Setting the Bplm with Pink NoiseSetting the Bplm without Pink Noise Menu .to .make .further .adjustments .if .neededEnabling THX Surround EX Decoding Changing Dolby Plii Music SettingsEnabled SP2 Surround Modes Changing DTS NEO6 SettingsCenter Image is a variable in Neo6 music mode only Appendix aWas .being .performed Ers Surround .ModesNatural .This .mode .enhances .the .basic .ste Infra-red remote codes SP2 SpecificationsAppendix B SP2 PREAMP/PROCESSOR Suggested Surround Speaker Placement

SP2 PREAMP specifications

The Bryston SP2 preamplifier stands as a hallmark of high-performance audio engineering, designed to deliver an exceptional listening experience to audiophiles and home theater enthusiasts alike. This remarkable component is not only a testament to Bryston's commitment to quality but also incorporates advanced technologies that cater to a wide range of audio applications.

One of the standout features of the SP2 is its extensive connectivity options. The preamp offers multiple analog and digital inputs, including balanced XLR, unbalanced RCA, and a variety of digital formats such as coaxial, optical, and USB. This versatility allows users to seamlessly integrate the SP2 into their existing audio systems, accommodating a plethora of sources ranging from traditional vinyl players to modern digital streamers.

Incorporating advanced digital signal processing (DSP), the SP2 also features room correction capabilities, enabling users to tailor their audio experience to the unique acoustics of their space. This technology optimizes the sound output, ensuring that every note and nuance is delivered with precision, regardless of environmental factors. Users can benefit from improved spatial imaging and clarity, leading to a more immersive soundstage.

The SP2 also boasts a high-quality D/A converter, which enhances audio playback realism. Capable of decoding high-resolution audio formats, it ensures that even the most intricate details in a recording are accurately reproduced. With support for sample rates up to 192 kHz, the SP2 promises a listening experience that is both engaging and true to the original recording.

Another prominent feature of the Bryston SP2 is its customizable processing options, including bass management and surround sound processing. This allows for an optimized audio experience whether listening to music or immersing in a cinematic adventure. The flexibility of adding or bypassing various sound modes provides users with extensive control over their audio experience.

Built with Bryston's renowned reliability, the SP2 is constructed with premium components that provide durability and long-lasting performance. The design ethos emphasizes both elegance and functionality, making it an attractive centerpiece for any audio setup.

In summary, the Bryston SP2 preamp combines advanced technologies and thoughtful design to create a powerful audio tool. With its extensive connectivity options, superior D/A conversion, DSP capabilities, and robust build quality, the SP2 sets a high standard in the realm of audio preamplifiers, making it an ideal choice for enthusiasts seeking an unparalleled listening experience.