Leviton Scene Capable Electronic Switch installation instructions Introduction, Features

Page 1

Single Pole (One location) or 3-Way (Multi-location)

 

Scene Capable Electronic Switch

Compatible with

TMenabled products!

 

Cat. No. RZS15-1L, (Lighted)

 

 

 

Incandescent-1800W – Magnetic Low-Voltage-1800VA (1440W)

 

 

DI-000-RZS15-00A-X3

Electronic Low-Voltage-1800WFluorescent-1800VASupplemental-1/2 HP

 

 

120VAC, 60Hz

 

 

 

 

 

Installation Instructions

WARNINGS AND CAUTIONS:

To be installed and/or used in accordance with appropriate electrical codes and regulations.

If you are unsure about any part of these instructions, consult a qualified electrician.

Vizia™ RF electronic switches are not compatible with standard 3-way or 4-way switches. They must be used with compatible Vizia™ or Vizia™ RF controllers.

Recommended minimum wall box depth is 2-1/2".

WARNINGS AND CAUTIONS:

Use only one (1) ViziaTM RF electronic switch in a multi-location circuit with up to 9 ViziaTM coordinating remotes without LEDs or ViziaTM RF remotes for multi-location.

Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft (90 m).

Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.

Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

INTRODUCTION

Leviton’s Vizia™ RF Z-Wave™ components are designed to communicate with each other via Radio Frequency (RF) to provide remote control of

 

 

WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN

Step 1

 

 

OFF POWER at circuit breaker or fuse and test that power is off

 

 

before wiring!

Step 4a Single Pole Wiring Application:

Terminal

Screw marked

 

 

3-Way Wiring with Coordinating Remote

Step 4b

 

 

(no LED) Application:

 

 

 

 

 

your lighting. Using RF technology allows Leviton to provide the greatest signal integrity possible. Each module in Leviton’s Vizia™ RF component line is a Z-Wave™ enabled device. In a Z-Wave™ network, each device

/&&

/.

/&&

/.

/&&

/.

/&&

/.

/&&

/.

/&&

/.

White (WH)

Coordinating Remote

Switch

Terminal

Screw marked

White (WH)

is designed to act as a router. These routers will re-transmit the RF signal from one device to another until the intended device is reached. This ensures that the signal is received by its intended device by routing the signal around obstacles and radio dead spots. The Scene Capable Plug-In Appliance Module is compatible with any Z-Wave™ enabled network, regardless of the manufacturer and can also be used with other devices displaying the Z-Wave™ logo.

/&& /./&& /.

/&&

/.

/&&

/.

/&&

/.

/&&

/.

Step 2 Identifying your wiring application (most common):

NOTE: If the wiring in your wall box does not resemble any of these configurations, consult a qualified electrician.

Terminal Screw marked Black (BK)

Terminal Screw marked Yellow/Red

BK WH

1

 

 

 

2

 

 

3

Yl/RD

RD

4

 

 

BK WH

 

 

2

 

 

1

 

 

3

Yl/RD

RD

4

 

 

 

5

 

 

1

Terminal

BK WH

 

Screw marked

 

2

Black (BK)

 

 

 

 

 

3

Terminal

Yl/RD RD

4

Screw marked

 

5

Yellow/Red

 

 

 

CAUTION:

Remember to exercise good common sense when using the Timer

Single Pole

1. Line (Hot)

3-Way

1. Line or Load (see

(Yl/RD)

Terminal

Screw marked

Red (RD)

(Yl/RD)

Terminal

Screw marked

Red (RD)

features of your Remote – especially when scheduling unattended devices. There can be some unexpected consequences if not used with care. For example, an empty coffee pot can be remotely turned on. If that should happen, your coffee pot could be damaged from overheating. If an electric heater is turned on by remote control while clothing is draped over it, a fire could result. DO NOT USE the remote for the control of high power heating appliances such as portable heaters. This device will not control

1

2

3

4

2.

Neutral

3.

Ground

4.

Load

1

3

4

5

2

 

 

important instruction)

2.

Neutral

3.

Ground

4.

First Traveler – note color

5.

Second Traveler – note

 

 

color

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Terminal label:

Use Terminal for 3-Way or More Applications Only. For Single-Pole Applications, Do Not Remove This label.

Switch

Coordinating Remote (no LED)

 

Switch

WH

BK

WH

Hot (Black)

 

(unused)

 

 

lighting that is used with electronic low-voltage and high frequency power supply transformers, nor high pressure discharge lamps (HID lighting). This includes mercury-vapor, sodium vapor and metal halide lamps.

FEATURES

Switch ON/OFF

Scene Capable

ON/OFF LED

Two way communication

RF reliability

Ease of installation – No new wiring

Compatible with other Z-Wave™ enabled devices

Tools needed to install your Switch

Slotted/Phillips Screwdriver

Electrical Tape

Pliers

Pencil

Cutters

Ruler

Changing the color of your Switch:

Your switch includes three color options. The switch ships with the White frame attached. To change color of frame, proceed as follows:

IMPORTANT : For 3-Way applications, note that one of the screw terminals from the old switch being removed will usually be a different color (Black) or labeled Common. Tag that wire with electrical tape and identify as the common (Line or Load) in both the switch wall box and remote wall box.

Step 3 Preparing and connecting wires:

This switch can be wired using side wire terminal screws or through backwire openings. Choose appropriate wire stripping specifications accordingly.

 

5/8"

Strip Gage

 

(1.6 cm)

 

(measure bare

Cut

 

 

wire here)

(if necessary)

 

 

 

 

WH

 

BK

Hot (Black)

 

 

 

 

 

 

 

Green

 

 

 

 

 

 

 

 

 

 

Ground

 

 

Black

RD

 

YL/RD

 

 

Line

 

 

 

 

 

 

 

Load

 

 

 

120VAC, 60Hz

 

 

Use Terminal for 3-Way or

 

 

 

 

 

 

 

 

More Applications Only.

 

 

White

 

 

For Single-Pole Applications,

 

 

 

Do Not Remove This Label.

 

Neutral (White)

WIRING SWITCH:

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot wall box wire to terminal screw marked "BK".

• Load wall box wire to terminal screw marked "RD".

• Line Neutral wall box wire to terminal screw marked "WH".

• Switch terminal screw marked "YL/RD" should have Red insulation

label affixed.

 

 

 

BK

 

Black

Green

 

Green

 

Ground

 

Ground

 

RD

YL/RD

 

YL/RD

Line

(unused)

 

RD

 

Load

120VAC, 60Hz

 

White

 

 

Neutral (White)

WIRING SWITCH:

Connect wires per WIRING DIAGRAM as follows:

NOTE: The switch must be installed in a wall box that has a Line Hot connection.

NOTE: Maximum wire length from switch to all installed remotes cannot exceed 300 ft (90 m).

• Green or bare copper wire in wall box to Green terminal screw.

Line Hot (common) wall box wire identified (tagged) when removing

 

old switch

 

to terminal screw marked "BK".

First Traveler wall box wire to terminal screw marked "RD"

Push in

Line up tabs

side at tab

and press in

to release

side to attach

INSTALLING YOUR SWITCH

NOTE: Use check boxes when Steps are completed.

Side Wire Connection

Back Wire (either hole may be used)

Side wire terminals accept #14

Back wire openings use #14-12 AWG

AWG solid wire copper only.

solid wire copper only.

Make sure that the ends of the wires from the wall box are straight (cut if necessary).

Remove insulation from each wire in the wall box as shown.

For Single-Pole Application, go to Step 4a.

For 3-Way Coordinating Remote (no LEDs) Application, go to Step 4b.

NOTE: If insulating label is not affixed to terminal screw marked "YL/RD",

use electrical tape to cover.

Proceed to Step 5.

(note wire color).

• Remove Red insulating label from terminal screw marked "YL/RD".

• Second Traveler wall box wire to terminal screw marked "YL/RD"

(note wire color). This traveler from the switch must go to the

terminal screw on the remote marked "YL/RD".

• Line Neutral wall box wire to terminal screw marked "WH".

Image 1
Contents Introduction FeaturesOperation TroubleshootingFCC Compliance Statement