Fortinet 224B manual To install firmware from a system reboot

Page 43


FortiGate Firmware	Installing firmware from a system reboot using the CLI

If you are reverting to a previous FortiOS version, you might not be able to restore the previous configuration from the backup configuration file.

Note: Installing firmware replaces your current antivirus and attack definitions, along with the definitions included with the firmware release you are installing. After you install new firmware, make sure that antivirus and attack definitions are up to date. For details, see the FortiGate Administration Guide.

To install firmware from a system reboot

1Connect to the CLI using the RJ-45 to DB-9 or null modem cable.

2Make sure the TFTP server is running.

3Copy the new firmware image file to the root directory of the TFTP server.

4Make sure the internal interface is connected to the same network as the TFTP server.

5To confirm the FortiGate unit can connect to the TFTP server, use the following command to ping the computer running the TFTP server. For example, if the IP address of the TFTP server is 192.168.1.168:

execute ping 192.168.1.168

6Enter the following command to restart the FortiGate unit.

execute reboot

The FortiGate unit responds with the following message:

This operation will reboot the system!

Do you want to continue? (y/n)

7Type y.

As the FortiGate unit starts, a series of system startup messages appears. When the following messages appears:

Press any key to display configuration menu..........

Immediately press any key to interrupt the system startup.

Note: You have only 3 seconds to press any key. If you do not press a key soon enough, the FortiGate unit reboots and you must log in and repeat the execute reboot command.

If you successfully interrupt the startup process, the following messages appears:

[G]: Get firmware image from TFTP server.

[F]: Format boot device.

[Q]: Quit menu and continue to boot with default firmware.

[H]: Display this list of options.

Enter G, F, Q, or H:

8Type G to get to the new firmware image form the TFTP server. The following message appears:

Enter TFTP server address [192.168.1.168]:

FortiGate-224B FortiOS 3.0 MR6 Install Guide
01-30006-0451-20080815	43

Image 43

Contents Install G U I D E Regulatory compliance TrademarksContents FortiGate Firmware Advanced configurationTesting new firmware before installing Installing firmware from a system reboot using the CLIIndex Page Register your FortiGate unit IntroductionAbout this document About the FortiGate-224BDocument conventions Typographic conventions Further ReadingFortinet Knowledge Center Customer service and technical supportComments on Fortinet technical documentation Environmental specifications InstallingRack mount instructions GroundingMounting Installed mounting brackets To install the FortiGate unit into a rackPlugging in the FortiGate Connecting to the networkTo power on the FortiGate unit To power off the FortiGate unitNAT mode NAT vs. Transparent modeTo connect to the web-based manager Connecting to the FortiGate unitTransparent mode Connecting to the web-based managerTo connect to the CLI Connecting to the CLITo configure interfaces Go to System Network Interface Configuring NAT modeUsing the web-based manager Configure the interfacesAdding a default route and gateway Configure a DNS serverAdding firewall policies To modify the default gateway Go to Router StaticTo set an interface to use a static address Using the CLITo set an interface to use Dhcp addressing To set an interface to use PPPoE addressing To configure DNS server settingsTo add an outgoing traffic firewall policy To modify the default gatewaySwitching to Transparent mode Configuring Transparent modeTo switch to Transparent mode Go to System Status Source Address All Destination Interface To switch to Transparent mode Backing up the configuration Verify the configurationSet the time and date Restoring a configurationAdditional configuration Set the Administrator passwordUpdating antivirus and IPS signatures Configure FortiGuardAdditional configuration Protection profiles Advanced configurationFirewall policies Firewall policiesAntivirus options Configuring firewall policiesAntiSpam options Web filtering Logging Downloading firmware FortiGate FirmwareUpgrading the firmware Using the web-based managerReverting to a previous version Using the USB Auto-Install Backup and Restore from a USB keyTo revert to a previous firmware version To upgrade the firmware using the CLI Using the CLITo revert to a previous firmware version using the CLI Execute restore image namestr tftpip4Execute restore image namestr tftpipv4 Installing firmware from a system reboot using the CLIPress any key to display configuration menu To install firmware from a system rebootTo backup configuration using the CLI Restoring the previous configurationTo restore configuration using the CLI Additional CLI Commands for a USB keyTo configure the USB Auto-Install using the CLI To test the new firmware image Testing new firmware before installingTesting new firmware before installing Testing new firmware before installing Index Web filtering 35 web-based manager Page Page