Enterasys Networks XSR-3020 manual Bootrom Monitor Mode Commands

Page 79

Bootrom Monitor Mode Commands

Bootrom is valid.

The software image in Flash is valid.

Bootrom Monitor Mode Commands

Bootrom monitor mode offers special user access when the XSR lacks valid software or runs abnormally. Enter the mode by pressing the key combination (CTRL-C) during the first five seconds of initialization. After you access the mode, list command groups by typing h to show the text below:

b Boot

f Files

n Network

sStatus

tTime and Date

D For Development Only

All the commands in each group can be listed by entering the command group letter. The main menu provides the following functions:

Reboot warm or cold

Update Bootrom

File system-related commands for the Flash ROM file system

Modify network parameters

Various status/show commands

Version number

Hardware information

Display crash info

Display or change date and time on real-time clock if present

Commands for development use only

Caution: Upon accessing Bootrom monitor mode, if you do not provide the password (if configured earlier with the bp command) when prompted or enter an incorrect password five times, the XSR will delete your configuration and reinstitute factory default settings. This function is similar to pressing the reset button on the XSR-1800 Series routers.

bc

This command initiates a cold reboot.

bw

This command initiates a warm reboot.

bp

This command changes the Bootrom password. The default password is blank. You are prompted to enter a password by the following script:

XSR Getting Started Guide 3-35

Image 79
Contents Version PeditionSecurity RouterPage Enterasys Networks, Inc Minuteman Road Andover, MA Regulatory Compliance Information Industry Canada Notices Product Safety Supplement to Product Instructions Vcci Notice N826 Enterasys Networks, Inc. Firmware License Agreement Page Page Contents BRI Leased Line BRI Leased Frame Relay BRI Switched Line Index Appendix a SpecificationsXiv About This Guide Contents of the GuideBold/En negrilla FTP Getting HelpXviii System Description OverviewPstn Hardware FeaturesXSR-3020 IP Protocol Software FeaturesOperating System Industry-common CLISnmp and Statistics Gathering IP RoutingFrame Relay SecurityIntegrated Services Digital Network Isdn BRI/PRI Dynamic Host Configuration Protocol DhcpVirtual Private Network VPN Quality of Service QoSGRE over IPSec Dial-on-Demand/Bandwidth-on-Demand DoD/BoD Dial ServiceDial Backup Asynchronous Digital Subscriber Line AdslInstallation Overview Installation Overview Introduction Installation Site SuggestionsVerifying Your Shipment Removing XSR Cover Installing NIM Cards and Rack MountingRemoving NIM Slot Cover Fastening Rack Brackets CompactFlash Card Installation Installing a CompactFlash Memory CardFormatting the CompactFlash Card CompactFlash Card for the Adsl NIMConnecting Serial COM Console Cable Connecting Cables11 Connecting High Speed Serial Connector 3020 15 Attaching Ethernet Connector 17 Attaching Ethernet LAN NIM Connector 19 Connecting Power Supply Cord Initializing XSR Software Software ConfigurationInitializing XSR Software Configuring RAI for Frame Relay Optional Configuring Remote Auto InstallOpening a COM Console Session Remote Auto Install Attempting Forever Configuring RAI over Adsl Configuring RAI for Dhcp over LANVirtual-template 1 pppoe limit per-mac Setting the Clock Configuring the XSR Name and User InformationSetting User Name, Privilege and Password Configuring the WAN Ports Configuring the LAN PortsPRI Configuration BRI Leased Line BRI ConfigurationBRI Leased Frame Relay BRI Switched Line PPPoE Adsl ConfigurationPPPoA IPoA Firewall Sample ConfigurationXSR with Firewall Topology Complete LAN and WAN interface configuration Setting Up RIP RoutingConfiguring Frame Relay Point to Point Networks Configure Ospf RoutingSetting Up an Snmp Community String, Traps and V3 Values Viewing Your Configuration Configuring Message Logging and Severity LevelProduct Version Connecting Remotely via the WebWeb Product Version Window Backup Site Hostname branch2 LAN-PPP Services Sample ConfigurationFrame Relay WAN Link with PPP Backup Sample Configuration Configure LAN Interface Configure Users and PasswordsConfigure Quality of Service XSRconfig-pmap-cpriority-server#priority medium 20 Configure WAN/Frame Relay PortConfigure More Access Lists Configure Ospf RoutingApply QoS Configure the Dial Backup Connection Configure DHCP/BOOTP RelayConfigure Snmp VPN Site-to-Site Sample ConfigurationGenerate Master Encryption Key Configure Access Control ListsSet Up IKE Phase I Security Configure IKE Policy for Remote PeerConfiguring VPN at Interface Mode and Setting Up RIP Configure Crypto MapsCreate a Transform Set Configuring Authentication AAA VPN Sample Configuration with Network Extension ModeVPN Topology with NEM, EZ-IPSec and Internet Access Create the Isakmp IKE global peer Initialization Output XSR Rebooting CharacteristicsReboot Triggers Reboot TriggersPower-up Error Conditions Bootrom Monitor Mode Commands Bootrom Monitor Mode Commands Del CopyDir Ffc Rename RemoveFTP Bootrom Monitor Mode Commands Bootrom Monitor Mode Commands Software Configuration System Specifications SpecificationsNIM WAN Cable, CompactFlash and Accessory SpecificationsXSR Getting Started Guide A-3 COM COM Console PortMini-GBIC Fiber, Copper Port GigabitEthernet PortsCopper/Fiber-optic Ethernet NIMs Regulatory/Safety Compliance21 DTE Port Serial NIM Card PortFigure A-8 EIA-232/530 DTE Pin Assignments Figure A-9 EIA-449 DTE Pin Assignments Figure A-10 Combined V.35/EIA-232/530 DTE Pin Assignments Figure A-11 DTE Pin Assignments T1/E1/ISDN PRI T1/E1/ISDN PRI NIM Card PortsGrounding Shunt for E1 NIM Cards Balun for E1 or PRI NIM CardsFigure A-16 Installing a Grounding Shunt on the E1 NIM Card Installing Shunt/Terminal StripFigure A-17 1-Port T3/E3 NIM Card T3/E3 NIM CardBRI-S/T Port BRI-S/T NIM Card PortsTermination Shunt for the Isdn BRI-S/T NIM Card Figure A-21 Isdn BRI-U NIM Card RJ-49C ports shown Port BRI-U NIM Card PortsFigure A-23 Adsl NIM Card Port Adsl NIM Card PortFigure A-25 T1/E1 D&I NIM Card T1/E1 Drop & Insert D&I NIMLED Behavior CompactFlash Memory CardPWR Index Index-2

XSR-3020 specifications

Enterasys Networks XSR-3020 is a sophisticated Layer 2 and Layer 3 switch designed to meet the demands of modern networking environments. Known for its robust performance and versatility, the XSR-3020 is an ideal solution for enterprises that require high efficiency, comprehensive security, and network reliability.

This switch supports a variety of advanced technologies, making it suitable for both data center and edge deployments. One of its standout features is its scalability. The XSR-3020 can accommodate growing network demands by allowing for easy integration of additional modules. This capacity for expansion ensures that organizations can adapt their networks without the need for complete hardware replacements.

The XSR-3020 offers high-speed connectivity through its multiple gigabit Ethernet ports, providing up to 48 10/100/1000BASE-T ports in a single chassis. This high-density design optimizes the physical space and ensures that organizations can connect numerous devices simultaneously without sacrificing performance. Additionally, it supports Power over Ethernet (PoE), allowing users to power network devices, such as IP cameras and access points, directly through the switch. This feature streamlines installations and reduces the clutter of electrical wiring.

Security is a critical consideration in today’s network landscape, and the XSR-3020 addresses this need with robust security features. It incorporates advanced access control capabilities, enabling administrators to segment traffic and enforce policies effectively. The switch also supports 802.1X authentication, ensuring that only authorized devices can connect to the network.

In terms of management, the XSR-3020 is designed to simplify operations through its user-friendly interface and extensive support for management protocols. It offers native support for Simple Network Management Protocol (SNMP) and can be easily integrated with various network management systems, allowing for efficient monitoring and troubleshooting.

Another key characteristic of the XSR-3020 is its reliability. With features such as redundant power supplies and fans, the switch ensures high availability, minimizing downtime for critical applications. It is also built to withstand harsh conditions, making it suitable for diverse environments.

Overall, the Enterasys Networks XSR-3020 combines high performance, scalability, and security, making it an excellent choice for organizations looking to enhance their network infrastructure. Its comprehensive set of features positions it as a reliable backbone for any modern enterprise network, ensuring that businesses can operate efficiently and securely.