4.Insert the board’s edge connector into the bus slot, and apply firm pressure to the top edge of the board until the board is fully seated in the edge connector.
| Remove | |
| Cover | PCI Express |
| Plate |
| Board |
| Computer |
| |
| Chassis | |
| | PCI Express |
| | Slots |
| | PCI Slots |
5.Reinstall the retaining screw.
6.Repeat steps 1 through 5 for any additional boards you are installing.
7.Connect the telephony boards together with a CT Bus cable of the appropriate size (not included). If possible, use a cable assembly that matches the number of boards in your system. If the cable has more than one unused connector, install the cable so that all the unused connectors are at one end of the cable.
CT Bus
ColoredCable Stripe
(Pin 1) 
Note:
Your CT Bus cable may have a different number of connectors (drops).
8.Replace the computer’s cover.
9.Reconnect the computer’s power cord.
6.Connecting to External Equipment
Each of the six RJ-14 jacks on the rear bracket of the Dialogic® D/120JCT-LS-EW board supports two analog telephony channels. A standard telephone will not function when directly connected to the board.
The following figure illustrates the pinout of the RJ- 14 jacks, which provide two tip/ring pairs with an earth recall, one set for each telephony channel.
Pinout for RJ–14 Jacks on D/120JCT-LSEW Bracket
| 6 | | | 6 | Line 2 Earth Recall |
| 5 | | | | 5 | Line 2 Ring |
| | | |
| 4 | | | 4 | Line 1 | Tip |
| | | |
| 3 | | | 3 | Line 1 | Ring |
| | | |
| 2 | | | | 2 | Line 2 | Tip |
| | | |
| 1 | | | 1 | Line 1 | Earth Recall |
| | |
7. After Installing the Board
If you are installing the Dialogic® D/120JCT-LS-EW in a system that already has the Dialogic® system release software installed, you may not need to install a new or upgraded software release to support the board. The Dialogic® D/120JCT-LS-EW has been designed to be compatible with existing System Release 6.x software versions that support
PCI boards. Please refer to the Release Update document for your release version for up-to-date information about support for PCI Express boards and any known issues relating to their use.
If this is the first Dialogic® telecom board you have installed in your system, you will need to install an appropriate version of the Dialogic® system release software and configure the software for the specific board(s) you are using. Refer to the installation and configuration documentation that accompanies the release for instructions.
When configuring the system for the Dialogic® D/120JCT-LS-EW board, use the same menu selections and configuration settings that are documented for the PCI version of the Dialogic® D/120JCT-LS.
8. Removing the Board
Removal of the Dialogic® D/120JCT-LS-EW board is essentially the reverse of the installation procedure:
1.Observe anti-static precautions.
2.Disconnect the telephony cables.
3.Remove the computer’s power cord.
4.Remove the computer’s cover.
5.Disconnect the CT Bus cable (if applicable).
6.Remove and set aside the board’s retaining screw.
7.Remove the board and place it static-protective packaging.
9. Contacting Technical Support
Dialogic provides technical support for its products through a network of value added distributors who are trained to answer technical questions on installing and configuring Dialogic® products. If you are unsure how to contact your support channel, please call Dialogic in the United States at 973-967-6600 (9am - 5pm EST) and we will assist in obtaining the appropriate support channel. Outside the United States please refer to http://www.dialogic.com/support/contact to obtain local contact information.
Dialogic also provides direct support via Dialogic® Pro™ Services agreements. For more details of direct support from Dialogic please refer to http://www.dialogic.com/support/DialogicPro.
10.Returning a Product
To return a board for warranty repair or any other returns, please refer to the following: http://www.dialogic.com/support/hwfaults
11.Warranty Information
For specific warranty information for this board, refer to the Warranty section of the Products page,
located at this URL: http://www.dialogic.com/warranties/.
12.Sales Assistance
If you have a sales question, please contact your local Sales Representative or the Regional Sales Office for your area. Address, telephone and fax numbers, are available at the Dialogic website located at: http://www.dialogic.com/contact.htm.
To purchase Dialogic® products, please refer to the following website to locate the appropriate supplier: http://www.dialogic.com/purchase.htm.
All contents of this document are furnished for informational use only and are subject to change without notice and do not represent a commitment on the part of Dialogic Corporation or its subsidiaries (“Dialogic”). Reasonable effort is made to ensure the accuracy of the information contained in the document. However, Dialogic does not warrant the accuracy of this information and cannot accept responsibility for errors, inaccuracies or omissions that may be contained in this document.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH DIALOGIC® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.
Dialogic products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications.
It is possible that the use or implementation of any one of the concepts, applications, or ideas described in this document, in marketing collateral produced by or on web pages maintained by Dialogic may infringe one or more patents or other intellectual property rights owned by third parties. Dialogic does not provide any intellectual property licenses with the sale of Dialogic products other than a license to use such product in accordance with intellectual property owned or validly licensed by Dialogic and no such licenses are provided except pursuant to a signed agreement with Dialogic. More detailed information about such intellectual property is available from Dialogic’s legal department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic encourages all users of its products to procure all necessary intellectual property licenses required to implement any concepts or applications and does not condone or encourage any intellectual property infringement and disclaims any responsibility related thereto. These intellectual property licenses may differ from country to country and it is the responsibility of those who develop the concepts or applications to be aware of and comply with different national license requirements.
Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and SIPcontrol, among others, are either registered trademarks or trademarks of Dialogic. Dialogic's trademarks may be used publicly only with permission from Dialogic. Such permission may only be granted by Dialogic’s legal department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Any authorized use of Dialogic's trademarks will be subject to full respect of the trademark guidelines published by Dialogic from time to time and any use of Dialogic’s trademarks requires proper acknowledgement. The names of actual companies and products mentioned herein are the trademarks of their respective owners.
