Eagle Tree Systems Seagull Glide manual Specifications, Transmitters

Eagle Tree Systems Seagull Glide manual Intended Uses, Packing List, Steps to Follow Eagle Tree Systems Seagull Glide manual Install your Data Acquisition Module Recorder, Important Warnings Eagle Tree Systems Seagull Glide manual Altitude Measurement Eagle Tree Systems Seagull Glide manual Powering the Glide Recorder, Installing the Seagull Transmitter in your Model Eagle Tree Systems Seagull Glide manual Eagle Tree Systems Seagull Glide manual Ready for Action, Adjusting the Variometer Eagle Tree Systems Seagull Glide manual Installing Temperature Sensors, Installing the RPM Sensor Eagle Tree Systems Seagull Glide manual Eagle Tree Systems Seagull Glide manual Setting up the Recorder with the Application, Removing the Recorder from your Plane Eagle Tree Systems Seagull Glide manual Telling the Recorder what to Log, Setting the Joystick Configuration Mode Eagle Tree Systems Seagull Glide manual Setting Metric or English Units, Seagull Configuration Wizard Eagle Tree Systems Seagull Glide manual Seagull Dashboard Data Setup Utility Instructions Eagle Tree Systems Seagull Glide manual Eagle Tree Systems Seagull Glide manual Using your Seagull in Laptop Live Mode, Configuring Variometer Alarms Eagle Tree Systems Seagull Glide manual Using the Recorder/Data Logger, Recorder’s LED Eagle Tree Systems Seagull Glide manual Recorder’s Pushbutton, After You’ve Flown Eagle Tree Systems Seagull Glide manual Saving Flight Files, Graphing/Spreadsheet Compatibility Eagle Tree Systems Seagull Glide manual Troubleshooting Eagle Tree Systems Seagull Glide manual Recorder FCC Information Eagle Tree Systems Seagull Glide manual Specifications, Transmitters Eagle Tree Systems Seagull Glide manual Limited Warranty, Etsi, Ce Eagle Tree Systems Seagull Glide manual Product Warranty Registration
Page 20

Page 20

Eagle Tree Systems SEA-01 (900 MHz, 200mW System)

Contains FCC ID: OUR-9XTEND (900 MHz, 1 Watt System)

Contains FCC ID: OUR-XBEEPRO (2.4 GHz System)

Tested to Comply With FCC Standards

FOR HOME OR OFFICE USE

FCC Radiation Exposure Statement Regarding the FCC Certified 900 MHz and 2.4 GHz

Transmitters

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be operated with minimum distance of 20cm between the radiator and your body.

The Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Caution

Any changes or modifications not expressly approved by the party responsible could void the user’s authority to operate this equipment.

Radio Interference and FCC Information

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help.

Specifications

FCC 900 MHz, 200mW Transmitter

 

Frequency Range:

902 – 928 MHz

Operating Range (Line of Sight):

up to 1.2 miles w/included antenna, up to 3.6 miles with RX Yagi

FCC Approval:

15.247 Frequency Hopping Spread Spectrum

Maximum Output Power:

approx 200 mWatt

Dimensions:

approx 2-3/4” x 1-1/4” x ¼”

Weight:

approx 0.5 oz (Transmitter only)

Temperature Range:

0 – 140 degrees F

TX Antenna:

Thin, flexible stainless whip

Power:

Power taken from Recorder/Receiver battery

Current Draw:

Transmitter + Recorder, average < 70 milliamp

FCC 900 MHz, 1 Watt Transmitter

 

Frequency Range:

902 – 928 MHz

Operating Range (Line of Sight):

Up to 14 miles (22 km) w/ included antenna, up to 40 miles with RX Yagi

FCC Approval:

15.247 Frequency Hopping Spread Spectrum

Maximum Output Power:

approx 1 Watt

Dimensions:

approx 1.44” x 2.38” x 0.20” (3.65 cm x 6.05 cm x 0.51 cm)

Weight:

approx 0.8 oz (Transmitter only)

Copyright © 2003-2005 Eagle Tree Systems, LLC

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Please read this manual before using your new system Intended UsesPacking List Steps to FollowImportant Warnings Install your Data Acquisition Module RecorderConnecting the Airspeed Pitot Tube Altitude Measurement Powering the Glide Recorder Installing the Seagull Transmitter in your ModelConnecting the Seagull Transmitter to your Data Recorder Using the Seagull Wireless DashboardPage Adjusting the Variometer Ready for ActionInstalling Temperature Sensors Installing the RPM SensorPage Setting up the Recorder with the Application Removing the Recorder from your PlaneSetting the Joystick Configuration Mode Telling the Recorder what to LogSetting Metric or English Units Seagull Configuration WizardSeagull Dashboard Data Setup Utility Instructions Page Servo Display on the Dashboard Using your Seagull in Laptop Live ModeConfiguring Variometer Alarms Using the Recorder/Data Logger Recorder’s LEDRecorder’s Pushbutton After You’ve FlownSaving Flight Files Graphing/Spreadsheet CompatibilityTroubleshooting FCC Information Recorder FCC InformationSpecifications TransmittersLimited Warranty ETSI, CEProduct Warranty Registration
Top Page Image Contents