Mark Levinson 53 owner manual Can’t Assign in ML Net

Page 30

 

Mark Levinson

 

rear panel Power switch, wait at least 10 seconds, then turn the

 

Power switch on). If the fault cannot be resolved, contact your

 

authorized Mark Levinson dealer or contact Mark Levinson

 

customer service.

Can’t Assign in ML Net

You must assign the slave from the master device. Verify that the

 

slave you want to assign is listed in the master device list and check

 

its current state. For further explanations on assigning slave devices,

 

refer to the owner’s manual of the master device.

No Response to

Commands in ML Net

26

Link2 Not Working

No Connectivity Via

Ethernet

1.Verify that the master device and the Nº53 are properly connected together with a router.

2.Verify that the Nº53 network setup is correct. Access to the internal Web page via a computer is required to verify the network settings of the Nº53. You may have to use the router status to verify network connectivity.

3.If status information is received on the master device, but commands cannot be sent to the amplifier, then verify that a Link2 connection does not also exist to the amplifier. If both Link2 and ML Net are connected to the amplifier, the Nº53 ignores ML Net commands but status information is still sent.

1.Verify that all devices are properly daisy-chained.

2.Refer to the product documentation of each device to verify compatibility and the proper cabling.

3.Power down all of the devices, then power up the master device, followed by each slave device. Allow each device to go through its initialization process before powering up the next device.

Then cycle the master device through Standby mode. The Standby LEDs should now be blinking in unison.

1.Verify that the network cables are properly connected between the router, switch, or hub and the Nº532. If connecting to a computer, verify that the computer network cable is in the correct port.

2.Verify the age of the router, switch, or hub. There may be a communication issue with the Nº532 and older network devices. Power cycle the Nº532 and use a newer router, switch, or hub between the network and the Nº532.

3.If connected directly to the computer, make sure a crossover cable is used.

4.Verify that the router and computer have valid IP addresses.

Page 29 Page 31
Image 30
Page 29 Page 31
Contents No53 Reference Power Amplifier FCC Notice Important Safety Instructions IiiDocumentation Conventions Safety Terms & SymbolsTerms in This Manual Symbols on Product Mark LevinsonTable of Contents Introduction Product DescriptionNº53 Power Amplifier What’s in the Box QuantityProduct Registration Unpacking Installation ConsiderationsPlacement VentilationWith ground-lifter or cheater adapters. Doing so may cause Power RequirementsMake Sure all components are properly grounded. Do not Result in personal injuries and/or product damageOperating States Status LED Front PanelFront Panel Standby ButtonRear Panel PowerPower Switch ~ AC Mains Relay AC input ~ AC MainsLoudspeaker Binding Posts InputPin Assignments Trigger Input and Output Power Save Mode SwitchControl Link2 PortsMark Levinson Ethernet Port Network Setup Material RequirementsTo Connect Without a Router Computer Requirements Connecting the CablesTo Connect Using a Router Computer No53 Crossover Cable No53 ComputerNetwork Setup Parameters Internal WebConnecting With Dhcp Recommended Setting Up Computer Nº53 Power Amplifier Network Setup for Windows XP Network Setup for WindowsConnecting With Static IP AddressingDirect Connection To change the host name of the amplifierTo change the IP address of the amplifier Mark Levinson Masters and Slaves Connecting the Devices ML NetFigure below illustrates a typical ML Net setup Discovering Slaves ML Net and Link2Status Reporting Fault Reporting Link2 Troubleshooting No Power Standby LED is off No OutputCan’t Assign in ML Net Restoring Factory Defaults If All Else FailsFault Protection ML Net Fault ConditionsCare & Maintenance Specifications Input & Output Connectors0DUN/HYLQVRQ1R OEV Declaration of Conformity Manufacturer

53 specifications

The Mark Levinson No. 53 is a strikingly sophisticated amplifier that epitomizes high-end audio engineering. With advanced technology and meticulous craftsmanship, the No. 53 is tailored for audiophiles who demand both power and musicality. This amplifier is designed to elevate the home listening experience to unprecedented heights, featuring an innovative combination of performance, flexibility, and aesthetic appeal.

One of the key features of the Levinson No. 53 is its impressive power output. Delivering 200 watts per channel into 8 ohms, the amplifier can drive even the most demanding speakers with ease. When connected to 4-ohm speakers, the power increases to an astounding 400 watts per channel. This enables the No. 53 to reproduce dynamics with authority, ensuring that the grand intentions of artists are faithfully conveyed.

The No. 53 also utilizes advanced Class AB amplification technology, which combines the best attributes of both Class A and Class B amplifiers. This not only ensures low distortion but also provides a warm, rich sound that retains clarity and detail. The unit's dual-mono design further enhances its performance, isolating each channel for optimal sound stage and imaging.

In terms of connectivity, the Mark Levinson No. 53 offers a variety of input options. It includes both balanced XLR and unbalanced RCA inputs, allowing seamless integration with a range of source components. This versatility ensures that users can indulge their preferences for different sources and systems without compromising sound quality.

Another remarkable aspect of the No. 53 is its robust build quality. The chassis is made from high-grade aluminum, which not only adds aesthetic appeal but also reduces resonance, leading to cleaner audio reproduction. The front panel features a refined design with an elegant display, giving users a clear visual interface to monitor settings and performance.

Technologically, the Levison No. 53 is equipped with proprietary Harman technology, ensuring that the amplifier maintains stable performance under various conditions. Furthermore, advanced thermal management systems are incorporated to prevent overheating during extended listening sessions, ensuring reliability and longevity.

In conclusion, the Mark Levinson No. 53 amplifier stands as a pinnacle of modern audio engineering, delivering breathtaking sound quality, exceptional power, and a feature-rich design. Whether you are an audiophile or simply a music lover, the No. 53 promises to redefine your listening experience, making it a worthy addition to any high-end audio system.
Top Page Image Contents