Proving Switch Adjustments, Wiring | Field Controls CK-43 manual

Figure 10

Figure 11

Figure 12

Diagram A

PROVING SWITCH ADJUSTMENTS

After proper air flow is established, the pressure switch adjustment is made by turning pressure switch adjustment screw clockwise (See Figure 10) until burner operation stops. Turn the adjustment screw counter clockwise until burner ignites. Turn the adjustment screw an additional 1/4 to 3/4 turn counterclockwise to ensure adequate switch adjustment.

WARNING: Failure to properly adjust the pressure switch as specified above could lead to improper operation of the pressure switch which will result in a hazardous condition and bodily harm!

THERMOSTAT HEAT ANTICIPATOR ADJUSTMENT

After venting kit installation and checkout, check the amperage current draw through the thermostat circuit and adjust the thermostat anticipator accordingly.

POST PURGE TIMER ADJUSTMENT

To adjust the post purge time, refer to Figures 11 & 12.

For timer that looks like Figure 11: Rotate the timer adjustment on the timer clockwise to increase the operation time. To decrease the operation time, rotate the timer adjustment counterclockwise.

For timer that looks like Figure 12: Rotate the timer adjustment on the timer counterclockwise to increase the operation time. To decrease the operation time, rotate the timer adjustment clockwise.

*Typical post purge time should be between 3 to 5 min.

WIRING

CAUTION: Disconnect electrical power when wiring power venter.

NOTE: If using this control kit with an electronic thermostat you need an RJR-5 isolation relay. Wire the venter

motor and controls in accordance with the National Electrical Code,

manufacturer's recommendations and/or applicable local codes. UNITS MUST BE GROUNDED. Check ground circuit to make certain that the unit has been properly grounded. The wiring

should be protected by an over current circuit device rated at 15 amperes.

CAUTION must be taken to insure that the wiring does not come into contact with any heat source. All line voltage

and safety control circuits, between the

venter and the appliance, MUST be wired in accordance with the National Electrical Code for class one wiring or equivalent methods. Route the venter motor and control wiring with an appropriate wiring method. Refer to the Wiring Diagram A.

Page 5

CK-43 specifications

The Field Controls CK-43 is a cutting-edge ventilation solution designed to enhance indoor air quality and optimize energy efficiency in residential and commercial settings. Known for its robust features and advanced technologies, the CK-43 ensures that spaces stay comfortable and healthy while reducing energy consumption.

One of the standout features of the CK-43 is its innovative demand-controlled ventilation system. This technology intelligently adjusts airflow based on real-time indoor conditions, such as the presence of occupants and the level of indoor air pollutants. By continuously monitoring these parameters, the CK-43 can deliver the precise amount of fresh air needed, eliminating the inefficiencies associated with traditional fixed ventilation systems.

The CK-43 is also equipped with a high-efficiency motor that operates quietly and reliably, ensuring that occupants remain comfortable without disruptive noise. This motor is designed to work seamlessly with the unit's variable speed settings, allowing users to customize airflow levels according to their specific needs. This versatility extends the unit's usability across different environments, from homes to commercial buildings.

Another key characteristic of the CK-43 is its advanced filtration system. The unit is designed to accommodate multiple types of filters, including HEPA filters, which capture a significant percentage of airborne particles, allergens, and contaminants. This ensures that users breathe cleaner air, contributing to better health and well-being indoors.

The CK-43 also features an intuitive control interface, allowing users to easily set their preferences and monitor system performance. This user-friendly design makes it accessible for individuals without extensive technical knowledge, ensuring that everyone can benefit from improved air quality.

Moreover, the CK-43 is built with durability and sustainability in mind. Constructed from high-quality materials, it is designed to withstand the rigors of continuous use while minimizing environmental impact. Its energy-efficient operation not only lowers utility bills but also aligns with modern energy-saving practices.

In summary, the Field Controls CK-43 is an innovative ventilation solution that combines advanced technologies, user-friendly features, and a commitment to improved indoor air quality. With its demand-controlled ventilation, high-efficiency motor, and versatile filtration options, the CK-43 is a vital addition to any space seeking to enhance comfort and health while promoting energy efficiency.