Parameter feedback is enabled in all stand-alone modes. Other stand-alone modes may cause undesirable MIDI loops. In stand- alone mode 3, the control data of your B-CONTROL is routed to the MIDI output B without the merge function.
Your B-CONTROL can also control your computer via MIDI (without a USB connection) as long as your computer features a MIDI interface. In this case, all stand-alone modes can be used. To utilize parameter feedback, you should still use the stand-alone mode 4. Alternatively, you can also use S-3 and connect the computer via MIDI OUT B so that no MIDI feedback loop is created.
4.2 “Play” mode menu
The Play mode menu is the highest menu level in the B-CONTROL. Use it during normal operation for real-time control of MIDI data.
Display:
After switching on the unit, the current system software version is briefly displayed. Value changes are shown when using one of the control elements, provided that they have been activated.
Control elements:
You can use several keys, encoders and faders simultaneously and send their MIDI data. The classification of MIDI data types is explained in chapter 4.4. According to its assigned MIDI data type, each control element shows the current parameter value in the corresponding LED or LED ring.
The position of the faders changes automatically as soon as you choose another preset or during incoming parameter messages.
LED display:
The encoder LED ring displays or the status LEDs of the buttons change automatically when running controller recordings in a sequencer, provided, of course, all connections have been made correctly, the correct operating mode is enabled and the software sequencer supports sending parameter values.
Button illumination varies according to the controller mode: if a button is in “Toggle on” mode, the button LED illuminates as soon as the button is pressed. Only when you press the button once again, the LED goes out. If a button is in “Toggle off” mode, the corresponding LED will be lit only for the time the button is pressed.
The performance of the control elements, the display and the LED displays can be individually set up and is explained in chapter 4.3 “Programming”.
4.2.1 Selecting a preset
sSelect a preset with the PRESET button 
. The new preset number is indicated in the display.
sAlternatively, you may select a preset by pressing and holding down the preset button while moving one of the
push encoders 
.
sAs soon as you release the PRESET button, the new preset is active.
4.2.2Copy/store presets
sPress the STORE button to save a preset. The button LED starts to flash.
sSelect a memory number using the PRESET buttons or by holding down one of the PRESET buttons while moving a push encoder at the same time. The new preset number flashes in the display.
sBy pressing STORE again, the STORE LED and the display stop flashing.
sIf you want to overwrite the current preset, press the STORE button twice (step 2 can be cancelled).
sCancel the store procedure by pressing the EXIT button.
We deliberately did not include an autostore function. That way, you can assign a new MIDI control to a control element without changing the current preset. If you want to restore a preset, just select another preset briefly and again return to editing. Now, the old data has been restored.
4.2.3 Copying encoder groups
With this function you are able to copy an entire encoder group within a preset. This saves a lot of programming effort if all encoder groups within a preset consist of the same basic functions (e.g. MIDI channel, CC number for turn and push function).
sPress the encoder group button of the group you want to copy.
sPress STORE; the STORE button LED flashes.
sNow select the destination encoder group. The destination encoder button LED flashes.
sPress STORE again, the STORE button LED is no longer lit.
sCancel the store procedure at any time by pressing EXIT.
+To permanently store encoder group settings, carry out the preset store function as explained in chapter 4.2.2.
+To copy an encoder group into a different preset, you have to copy an entire preset! After that, you can copy or rearrange the encoder groups in the new preset as described above.
4.3Programming
4.3.1 The LEARN function
The easiest way to assign MIDI functions to individual control elements is to use the LEARN function. Here, the MIDI data is assigned remotely. For example, MIDI data sent from a MIDI sequencer to your B-CONTROL is assigned to a control element selected beforehand.
With LEARN, not only CC, NRPN and note commands can be received but almost any type of MIDI data, including short SysEx strings.
sPress and hold the LEARN button while operating any control element. This can be a fader (BCF2000 only), an encoder BCR2000 only), a PUSH encoder, button, footswitch or sustain pedal (BCF2000 only). The control element is shown in the display (e.g. E 24 or Fd 8).
+When using push encoders, select an encoder group beforehand. In addition, you have to differentiate between turn and push function.
sNow, release the LEARN button. The B-CONTROL is waiting to receive MIDI data.
sStart transmitting MIDI data from your sequencer. As soon as the data is received by the BCF2000/BCR2000, it is shown in the display.
sAfter correct data transmission, the display shows “GOOD” or “bAd” if wrong, faulty or too extensive data has been sent.
sTo leave or cancel LEARN, press the EXIT button.
4.3.2 Programming in EDIT mode
Various types of MIDI commands (Pitchbend, After Touch, MMC etc.) are assigned to the individual control elements in EDIT mode.
sTo activate the EDIT mode, press and hold the EDIT button and operate a control element. This can be a fader, sustain pedal (BCF2000 only), an encoder (BCR2000 only), a push encoder, a button or footswitch. The control element is indicated in the display (e.g. E 24 or Fd 8).
+When using push encoders, select an encoder group beforehand. In addition, you have to differentiate between turn and push function.
FADER 
ROTARY BCR2000