ABC Office 852CC, 802CC manual Maintenance, Malfunction Technical Data, Accessories

GB

802CC 852CC

Schleicher International

CLEANING THE PHOTOCELLS (8) (Fig. 4):

If paper particles should come to rest in the inlet guide (for example after a paper jam) it is possible that the machine will not turn off, due to the broken light barrier.

To remove these paper strips and also to clean the photocell, pass another sheet of paper through the feed slot, or switch the machine to reverse and wipe both „eyes“ of the photocell with a brush.

MAINTENANCE

8

CUTTING SYSTEM MAINTANANCE:

After about 2 hours of continuous operation run the cutting system in reverse for about 30 seconds and, at the same time, spray some of the enclosed special oil onto the cutting system.

ENERGY SAVING TIP:

Be certain that the machine is turned off overnight (mains switch (1) (fig. 1) switched to „0“).

fig. 4

MALFUNCTION TECHNICAL DATA

TAKING OUT EXCESS PAPER

IN CASE OF OVERLOAD:

If the shredder has stopped due to an overload (motor protection) take the excess paper out of the inlet as follows:

1.Depress the reverse pushbutton (4) (fig. 2). The material is released.

2.Lift up the hopper. The pilot lamp „door open“ or „hopper open“ (7) (fig. 2) will light.

3.Remove the excess material by hand from the inlet guide.

Note: In this case, there is no danger of injury as all circuits are interrupted when the hopper is lifted and the machine cannot be started.

MOTOR FAULT:

The machine is equipped with a thermally protected motor. Should this motor be overloaded, it will switch off automatically. In such case the pilot lamp „ready“ (5) (fig. 2) flashes.

After a cooling down period of approx. 10 minutes (depending on the room temperature) you can restart the machine and continue shredding.

Note: When the motor is overloaded, only the		Cutting width:
forward run is cut off. To take the excess paper out		802CC:	1.9x15 (cross-cut)
of the inlet opening, the cutting system may at any		852CC:	3.8x40 (cross-cut)
time be switched on „reverse“.		Cutting capacity:
		802CC:	35-40 sheets (70 g/m2)
FAULT CHECKLIST:		852CC:	70-80 sheets (70 g/m2)
If the machine is not functioning properly, you		Working width:	444 mm
should check the following:		Power:	3.9 kW
-	is the plug conneted to the mains?	Supply voltage:	400V/50Hz
-	is the mains switch (1) turned on?		230V/50Hz
-	is the door closed?		415V/50Hz
-	is the collecting bag full?		220V/60Hz
	The bag has to be emptied.		200V/50Hz
-	is the motor overloaded?		200V/60Hz
	Please refer to the section headed „Motor Fault“.	Pre-fusing:
-	is there a phase failure?	(gl fuse, type 1 assignment)
	Check the three-phase fuse at the power supply	400V-415V/50Hz:	16 A
	socket, and replace if necessary.	220V-230V/50-60Hz:	25 A
		200V/50-60Hz:	25 A
If you still cannot isolate the fault after carrying		Width:	750 mm
out all these checks, please notify our customer		Depht:	550 mm
service department.		Height:
		802CC:	1275 mm
		852CC:	1600 mm
		Noise level:	approx. 75 dB(A)
		Weight:
		802CC:	approx. 185 kg
		852CC:	approx. 201 kg

ACCESSORIES

Description	Order-No.
Plastic bag, 600 x 380 x 1100 x 0,6 mm	80946
Lubrication bottle, 125 ml	99943

Note: For orders of special accessories and spare parts, please contact your dealer.

7 1-800-658-8788 - www.abcoffice.com