Hafler P7000 manual Installation, Balanced Input 1/4 Tip Ring Sleeve, Balanced Input XLR

Page 6

I N S T A L L A T I O N

LOCATION

The P7000 uses forced-air fan cooling to remove the heat produced in normal operation. Although this makes the amplifier less sensitive to ventilation than if it were passively cooled, fresh air flow at the mounting location must still be considered. The fan pulls in fresh air through the side vents and the heated air is forced out through the front panel. Another consideration when choosing the location for a fan cooled amplifier is its proximity to the listening position. In some situations the sound of the fan operation can be distracting.

The power transformer can generate a substantial magnetic field, so caution should be exercised in the placement of low level components such as a tape deck, mixer or mic preamp to avoid inducing noise in the low level circuitry. Allow several inches of clearance when mounting these components.

AC LINE

The P7000 operates from a 120 volt, 60Hz AC power line. Connection is made by 14 gauge, IEC Type 320, grounded line cord. For safety considerations only a properly grounded (earthed) receptacle should be used. If a grounded circuit is not available do not break off the ground pin; use the proper adapter plug for a two wire receptacle. The power line fuse is mounted on the rear panel of the amplifier. If this fuse blows replace it only with the same type and rating fuse. The correct replacement fuse value is printed on the rear of the amplifier and in the parts list.

INPUT

The input jacks used on the P7000 are dual function connectors which accept 1/4" (Tip Ring Sleeve) phone and XLR plugs. The amplifier will operate with either a balanced or unbalanced signal source. The connector pin- out is printed on the rear panel of the amplifier.

Balanced Input: 1/4" Tip Ring Sleeve

The 1/4" balanced input jack is connected according to conventional usage with the Tip high (+), Ring return (–) and the Sleeve ground shield.

Balanced Input: XLR

The XLR balanced input jack is connected according to the IEC and AES Standard, with pin 2 high (+), pin 3 return (–) and pin 1 ground shield. When preparing to use the amplifier, check the output configuration of the source unit to maintain the proper signal polarity.

Unbalanced Input

Many popular mixers use unbalanced RCA phono or 1/4" phone jacks for the monitor outputs and can be used with the P7000 for short cable runs. The specifications for the mixer should give the maximum cable length it is capable of driving. The return (–) terminal must be grounded when using the amplifier with the input unbalanced to prevent unstable operation.

Unbalanced Source with Balanced Input

Some systems will have a noticeable amount of residual ground noise when run with unbalanced signal lines. Better noise rejection can be achieved in these systems by using shielded, twisted pair (balanced) cable from the unbalanced source. At the source end of the cable, connect an RCA or 1/4" phone plug with the return (–) wire and shield connected to the ground terminal of the plug. Wire the plug at the amplifier end of the cable the same as for the regular balanced input connection described above.

– 2 –

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Trans Follow Instructions R F O R M a N C E Specification S Operation InstallationB L E O F C O N T E N T S Technical ReferenceT R O D U C T I O N Balanced Input XLR InstallationBalanced Input 1/4 Tip Ring Sleeve Unbalanced InputTwo-Channel Stereo Dual MonoBridged Mono E R a T I O N Stereo/Bi-AmpNormal/Bridged Thermal SignalClipping ShortField Service Considerations C H N I C a L R E F E R E N C EPC B O a R D L a Y O U T Page R T S L I S T CER-106SM P7000 Functional Block Diagram Circuit Operation Transnova ImplementationFan Speed Regulation Thermal Protection Amplifier Module Replacement Wire Color Function TerminalHigh Pass Low Pass Full Range Building Custom XcardsResistor Chart Butterworth Alignment Q =SE R V I C E P O L I C Y a N D LI M I T E D W a R R a N T Y

P7000 specifications

The Hafler P7000 is a professional power amplifier renowned for its robust performance and reliability in live sound and studio applications. A cornerstone of the Hafler brand, the P7000 embodies advanced technology and engineering, making it a popular choice among audio professionals.

One of the standout features of the P7000 is its high power output. It delivers up to 700 watts per channel at 4 ohms, providing ample headroom for demanding audio environments. This powerful output makes it suitable for driving large loudspeakers or multiple speaker systems, ensuring clear and dynamic sound reproduction even at high volumes.

The P7000 utilizes a class AB amplifier design, combining the benefits of class A and class B architecture. This design choice ensures low distortion levels while maintaining efficient operation. As a result, users can expect a warm and natural sound with low signal degradation, making the amplifier ideal for critical listening environments.

In terms of build quality, the Hafler P7000 is constructed with durability in mind. The chassis is made from robust materials that can withstand the rigors of frequent transport and use in various settings, from professional studios to live concert venues. Additionally, the amplifier features a well-ventilated design, minimizing overheating and ensuring reliability during extended operation.

The P7000 also includes advanced protection circuitry to safeguard against overload and short circuits. This feature not only protects the amplifier itself but also the connected speakers, providing peace of mind during high-energy performances. Furthermore, the amplifier incorporates a soft start circuit, which gradually ramps up power to the speakers, preventing sudden jolts that could cause speaker damage.

Connectivity is another key aspect of the Hafler P7000. It offers a variety of input options, including XLR and 1/4" TRS connectors, making it compatible with numerous audio sources and easy to integrate into any existing setup. Balanced inputs help reduce noise and interference, ensuring clean signal transfer over long cable runs.

With its combination of powerful output, reliable performance, and versatile connectivity, the Hafler P7000 stands out as a professional-grade amplifier. Whether used in a studio setting or live sound application, it provides audio professionals with the tools they need to achieve exceptional sound quality and consistency.
Top Page Image Contents