Lumens Technology DC260 user manual „ EN55022 CE Radiation Warning

Page 7
„EN55022 (CE Radiation) Warning

OPERATE THE EQUIPMENT.

Note: This equipment has been tested and found to comply with the limits for a Class A or B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Notice:

(1)A Unshielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cords by used.

(2)Use only shielded cables to connect I/O devices to this equipment.

(3)Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

„EN55022 (CE Radiation) Warning

This product is intended for use in a commercial, industrial, or educational environment. It is not intended for residential use.

This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.

English - 6

Image 7
Contents User Manual DC260 Visual PresenterContents ChapterTroubleshooting Connecting to MicroscopeCopyright Information Chapter 1 Precautions „ FCC Warning „ Safety Precautions„ EN55022 CE Radiation Warning Chapter 2 Package Content Bottom English Chapter 3 Product Overview8. Gooseneck 7. AF button 4. LED indicator 1. Lamp 3. Control panel 2. Remote sensor 9. Built-in icrophone 5. Lens 6. DIP switchDocument 3.1 Relative position of the presenter and DC2603.2 Recommend distance DC2603.3 Incorrect use Monitor Projector PC Microphone Chapter 4 Installation and Connections4.1 System diagram connecting to theNote Appearance of power cord may vary with countries/regions 4.3 Connecting devices4.3.1 Step 1 Plugging in the power outlet ¾ Connecting to a TV„ PAL Country/region not listed above ¾ Connecting to a computer ¾ Connecting to a LCD TV/ PDPMicrophone English ¾ Connecting to speaker¾ Connecting to microphone Speaker4.5 Installing remote control holder 4.4 Start using the DC2604.6 Installing application software 5.1.1 XGA 60Hz output default values Chapter 5 DIP Switch Settings5.1 Connecting to a projector or monitor Note You have to reset the unit for setting to take affect5.2.2 PAL Countries/regions not listed above 5.2 Connecting to a TVAuto Tune Chapter 6 Control Panel/Remote Control and Setting Menu6.1 Functions of control panel and remote control Remark The below functions are listed alphabeticallyMode LampM Scope Menu2nd Level 6.2 Setting MenuAdjustment 1st Levelto play the slides StorageUser Manual Chapter functions 7.14 I would likeSingle SettingImage Quality MediumReduction VolumeNoise DC260 User Manual ChapterEnglish Chapter 5 DIP “Switchpassword Advancefactory default setting Preset LoadPreset Save Factory Reset7.2 I would like to make text clearer and photos more colorful 7.1 I would like to switch image sourcesRemote control Chapter 7 Descriptions of major functions7.6 I would like to turn on/ off the lamp 7.5 I would like to adjust the brightness7.8.1 Setting the quality of captured images 7.4 I would like to use the auto focus7.9 I would like to view captured images 7.8.2 Setting continuous capture1. Press Capture on the remote control or control panel 1. Press Source on the remote control or control panel7.12.3 Playing videos 7.12.1 Setting the image quality7.12 I would like to record and play videos 7.12.2 Recording videos7.14.2 Setting delay time 7.14.1 Setting the slide show effect7.14 I would like to play the slides Slide Show Captured Image Live Image 7.14.3 Activating/Stopping the slide show7.17 I would like to reduce the image noise Noise Reduction 7.16 I would like to resume the factory default setting Factory ResetConfirm password 7.18 I would like to set / change the password Lock Down7.18.1 Setting the password Key in Password7.19.2 Inserting a SD card 7.19 Using a SD card7.18.2 Changing the password 7.19.1 Deactivate the write protect function SD Lock7.20.1 I would like to insert a photo in MS-Paint 7.20 Computer-related functions7.19.3 Ejecting a SD card 1. Click Insert Image From Scanner or Camera in MS-Word 7.20.2 I would like to insert a photo in MS-Word3. A window showing a live image see below will be displayed English 2. Select Visual Presenter V2 TWAIN and click Custom Insert7.20.4 I would like to set the DC260 as a webcam for Skype Manual Chapter 6 Control Panel / Remote Control and Setting Menuo n p 7.20.5 I would like to set the DC260 as a PC Camera 7.20.6 I would like to set the DC260 as a Removable Disc USB Cable PC Interactive Whiteboard 1.System diagram2. Using StarBoard 7.20.7 I would like to connect Interactive Whiteboard3. Using SmartBoard 3.1 Press Insert / Picture From Scanner 3.2.Control panel Chapter 8 Connecting to Microscope4. Press f or e to select Normal English 2. Press f or e to select Display 3. Press d to select ModeBoot without Chapter 9 TroubleshootingIssues Solutions