Installation, Operation | Hafler DH-200 specs

INSTALLATION

The DH-220is most likely to be installed out of sight in most applications, since its power may be controlled by the AC switching of most audio preamplifiers, like the Hafler DH-110. If your control unit does not provide switching capacity sufficient for the amplifier’s 7 amp needs (plus other equipment it is also switching), you should use the amplifier’s own power switch. In that case, turn on the preamplifier first; then turn the amplifier on a few seconds after the preamp has been turned on, to avoid any unnecessary turn-on transients from some preamplifiers. Likewise, switch the power amplifier off first.

If the amplifier is to be installed close to a record player, you should first check its position for freedom from hum pickup by the cartridge from the field radiated by the power transformer of the DH-220. Although the design of the transformer minimizes such radiation, certain cartridges are more sensitive

than others, and require separation from the amplifier. Check at a comparatively high volume setting, and while swinging the tone arm throughout its arc. Often a few inches additional spac- ing will eliminate the problem.

Be sure to provide sufficient ventilation for the amplifier. Unobstructed air circulation around the finned heat sinks and above the amplifier is important for long, trouble-free life. Never put anything on top of the cover perforations. It is normal for the top and the heat sinks to become warm in use.

It is expected that the amplifier will always be resting on its feet, which should be on a hard enough surface that air flow underneath is not obstructed. If it is mounted in a rack, or through a panel, the feet may be removed so long as adequate ventilation is provided through the bottom openings.

OPERATION

The red pilot lamp which is integral with the power switch glows whenever the amplifier is turned on. A blown AC line fuse is the most likely cause if it is not illuminated when the amplifier is switched on.

The pilot lamp also provides a high temperature indication. In the unlikely event that the amplifier ceases to function, and the amp blinks on and off steadily, it indicates that one of the ther- mal breakers has shut down the amplifier because of excessive temperature rise in a heat sink. When the heat has dissipated in a few minutes, the amplifier should return to normal operation. If the lamp again blinks, check for insufficient ventilation, or an excessive input signal, or an input which may have dangerous signal content (such as oscillation). Failing evidence of this, the amplifier may have malfunctioned. Because of the very large heat sinks, it is highly unlikely that any normal signal will cause the amplifier to overheat.

Loudspeaker Fuse Selection

The DH-220 power amplifier is supplied with 2 amp fuses in the speaker lines. Experience has shown that since an overload must exist for a few seconds for a fuse to blow, a 2 amp fuse will protect most speaker systems, and only blow when overload oc- curs. Smaller fuses tend to blow too easily, and larger fuses do not adequately protect most speaker systems.

A pair of 5 amp fuses are also supplied as alternatives for the speaker fuse holders. These should be substituted if the power output of the amplifier is to be tested, and these or intermediate values may be used if the amplifier is to be operated at very high power levels into 4 ohm loads.

If the manufacturer of your speakers recommends a specific value of fuse for their protection, we suggest that you obtain A C fuses of that value and install them in the back panel.

Loudspeaker Power Ratings

There are no U.S. standards for rating the power handling of loudspeakers. As a result, the manufacturers’ usual “music power” ratings, or suggested amplifier limits, are of only minimal help in determining safe operating levels with amplifiers which can deliver substantial amounts of power. You must take into consideration the type of music, and the levels you like, to provide long term trouble-free operation of your speaker choice, when you have a sizeable amplifier like the DH-220.

Connections

The AC power cord should be plugged into 120 volts, 60 Hz, on the switched outlet of a preamplifier which can provide at least 7 amps, or 840 watts. Then the amplifier power switch may be left on, and it will be controlled by the rest of the system. Or. it may be plugged into a 120 volt wall outlet, and switched on and off independently.

If your line (mains) voltage is different, be sure you have the alternate power transformer which can accommodate several line voltages, and be sure it is wired for your mains voltage as described later in this manual before you pIug in the amplifier.

Input

Conventional shielded cables, such as those supplied with your preamplifier, provide the input signal to the sockets on the back panel of the DH-220. Be sure that the outer shield connec- tion is secure, to avoid hum. The length of these cables (so as to permit remote location of the amplifier, if desired) is limited only by the output impedance of the preamplifier. If it is 600 ohms or less, as with the DH-101and DH-110 Hafler preamps, for in- stance, cable lengths up to 50 feet are premissible without loss of

DH-200 specifications

The Hafler DH-200 is a well-regarded power amplifier that has earned a dedicated following among audio enthusiasts since its release in the early 1980s. Known for its excellent performance and reliability, the DH-200 has become a staple in many home audio systems.

One of the key features of the DH-200 is its high power output, delivering 100 watts per channel into 8 ohms and 200 watts into 4 ohms. This robust power handling capability makes it suitable for driving a wide range of speakers, from compact bookshelf models to larger floor-standing designs. The amplifier's low distortion and high current output ensure that it can reproduce dynamic and intricate musical passages with clarity and precision.

The DH-200 utilizes a unique circuit topology that incorporates a high-performance, complementary push-pull output stage. This design minimizes crossover distortion while providing excellent linearity and frequency response. The frequency response extends from 20 Hz to 20 kHz, matching the full range of human hearing and allowing for a natural reproduction of both low and high frequencies.

Another notable technology in the DH-200 is its use of a toroidal transformer, which contributes to the amplifier's efficiency and low noise operation. Toroidal transformers are known for their compact size, reduced electromagnetic interference, and improved power supply regulation, which translates into cleaner audio performance.

In terms of build quality, the Hafler DH-200 features a rugged chassis and a minimalist front panel design. The amplifier is a two-channel unit, with individual volume controls for each channel, allowing for precise adjustments. The rear panel is equipped with standard RCA input connections and binding posts for speaker outputs, making it compatible with most audio sources and speaker systems.

The DH-200 is also praised for its thermal management, featuring multiple heat sinks to dissipate heat effectively during extended use. This design helps to ensure long-term reliability, even under demanding listening conditions.

In conclusion, the Hafler DH-200 is a power amplifier that stands out for its exceptional sound quality, powerful performance, and robust build. Its combination of advanced technologies, such as a complementary push-pull output stage and toroidal transformer, make it an enduring choice for audiophiles seeking a reliable and high-performing amplifier for their home audio systems. Whether for casual listening or critical listening sessions, the DH-200 has proven to be a versatile and gratifying component in any audio setup.