Compatible Systems OCTAL V.35 manual Connecting a Line Device to the V.35 Interfaces

Page 7

Chapter 1 - Network Installation

3

The Octal V.35-Quad 10/100 RIOP is shipped with two “Quad” cables. These cables have a single Very High Density D-Sub connector which plugs into one of the Quad V.35 interface ports on the front of the device and then divides into four separate High Density D-Sub (HD D-Sub) female interface cables.

ϖNote: Port numbers 0 - 3 are stamped on both sets of Quad cables. For ports 4 -7, the connector marked “Port 0” is Port 4, the connector marked “Port 1” is Port 5, etc.

In addition, there are eight HD D-Sub male to V.35 male adapter cables. The V.35 male connector plugs into the female V.35 connector on the chassis of the V.35 line communications device. The pin outs for this cable are shown in Appendix A.

ϖNote: Please use only the supplied cables when connecting your V.35 line communication device to the Octal V.35-Quad 10/100 RIOP’s interfaces. The cables provided with other equipment will generally not have the same internal connections.

Connecting a Line Device to the V.35 Interfaces

These interfaces can be used to connect to a wide variety of line communications devices, including those which support either leased or dialed operation. Examples include leased 56K CSU/DSU’s, switched 56K CSU/DSU’s, fractional T1 CSU/DSU’s, ISDN terminal adapters, and full T1/E1 rate CSU/DSU’s.

Make sure that both units are powered off. First connect one of the eight V.35 adapter cables to the line communications device. Then connect one of the Quad cables to one of the V.35 inter- faces on the front of the router. Lastly, connect the two cable ends together. With each connec- tion, make sure to fasten the captive screws into the jack screws on either side of the connec- tors.

Connecting a Management Console

If you wish to connect an out-of-band management console, use the supplied DB-25 male to DB-25 female console cable and connect to the Console interface on the Octal V.35-Quad 10/100 RIOP. You can use a dumb terminal or a computer equipped with VT100 terminal emulation.

The default settings for the Console interface are VT100 terminal emulation, 9600 bps, 8 bits, no parity, 1 stop bit and no Flow Control.

ϖNote: The Octal V.35-Quad 10/100 RIOP also has an AUX interface. This is a modem connection which should only be used in consultation with Compatible Systems Technical Support staff, who will provide instruction on its use.

Powering Up the Router

Connect the supplied power cord to the front of the VSR and set the power switch to “On.” At power-up, the router will take approximately one minute to become visible to CompatiView.

ϖNote: If you want to use Telnet as a management method, you must first configure an IP address into the router with an out-of-band console, or reconfigure the IP address on an IP host or workstation on the same Ethernet segment as the router. See the appropriate VSR chassis section of the manual for more information on Command Line Management.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Octal V.35 Quad 10/100 Riop Installation Guide Page Quickstart Instructions Table of ContentsAppendix a Connector and Cable Pin Outs Shipping DefaultsLED Patterns LED Patterns Network InstallationQuickstart Configuration Shipping DefaultsConnecting the Octal V.35-Quad 10/100 to the Ethernet Network InstallationTelco Line Connection Requirements Connecting a Management Console Connecting a Line Device to the V.35 InterfacesPowering Up the Router Required for IP Ethernet Interface ConfigurationQuickstart Instructions IP ProtocolAppleTalk Protocol IPX ProtocolWAN Link Configuration WAN Interface ConfigurationPhysical Communications Settings PPP ConfigurationIP Protocol Frame Relay Dlci Mappings Frame Relay ConfigurationRequired for Dedicated Line Operation Required for IP Unnumbered Interface Required for IP Numbered InterfaceIPX Protocol Smds Addressing Smds ConfigurationSaving a Configuration File to Flash ROM Link ConfigurationEthernet Interfaces Shipping DefaultsWAN Interfaces Router LED Patterns LED PatternsOctal V.35-Quad 10/100 Riop LED Patterns Pin Outs for HD D-Sub Male to V.35 Male Cable Appendix a Connector and Cable Pin Outs

OCTAL V.35 specifications

Compatible Systems OCTAL V.35 is a sophisticated networking product designed to enhance communication among various devices within a digital network. This innovative solution incorporates advanced technologies that enable seamless data transfer, robustness, and versatility in diverse environments.

One of the hallmark features of the OCTAL V.35 is its octal architecture, which allows for multiple data connections simultaneously. This architecture is particularly advantageous for organizations that require high-bandwidth data transmission and need to connect numerous devices at once. The ability to manage several connections helps reduce latency and optimize network performance.

The OCTAL V.35 is equipped with V.35 interfaces, which are essential for high-speed circuit-switched data transmission. This makes it ideal for applications requiring reliable and fast data communication. Its compatibility with V.35 enables the device to support a variety of networking standards and protocols, making it an excellent choice for interconnecting legacy systems with modern technologies.

Another prominent characteristic of the OCTAL V.35 is its built-in redundancy features. To ensure uninterrupted service, the system is designed to automatically switch to backup connections in case of primary link failures. This ensures that critical data remains available and that operations continue seamlessly, providing peace of mind for organizations that rely on constant data flow.

The device also supports multiple operating modes, catering to various use cases. Whether it’s point-to-point, multipoint, or other networking configurations, the OCTAL V.35 can be easily tailored to meet the specific requirements of any application scenario.

Furthermore, compatibility with various network management protocols allows for easy monitoring and maintenance of the network, ensuring that performance levels are sustained and issues can be promptly addressed.

Security features are a priority within the OCTAL V.35. The system includes advanced encryption and access control protocols to safeguard sensitive data, making it suitable for use in environments where data security is paramount, such as financial institutions and healthcare organizations.

In conclusion, the Compatible Systems OCTAL V.35 combines cutting-edge technology with practical features to provide a versatile, reliable, and secure networking solution. Its ability to handle multiple connections, adapt to various configurations, and maintain security makes it an ideal choice for organizations seeking to optimize their digital communications.
Top Page Image Contents