IEEE1394 FireWire, I-Link Connection | Antec SX1000II, SX1000BII

IEEE1394 (FireWire, I-Link) Connection

There are six wires with connectors coming from the front mounted IEEE1394 port of your case. They consist of 2 sets of twisted pair cables; TPA (Twisted Pair A) and TPB (Twisted Pair B), a power cable (VP), and a ground cable (VG).

1.Locate and identify the pin-out of the IEEE1394 port on your motherboard.

2.Power Pin: Connect the VP connector to it.

3.Ground Pin: Connect the VG connector to it.

4.Data Pins: There are two sets of data pins. Each set consists of a plus and a minus pin. They are usually marked as TPA+ and TPA-, TPB+ and TPB-.

a.Connect the TPA+ connector to the TPA+ data pin and TPA- connector to the TPA- data pin.

b.Connect the TPB+ connector to the TPB+ data pin and TPB- connector to the TPB- data pin.

3.5" Device Installation

With the front bezel facing you, swing the plastic bezel cover out. You can see there are four 5.25" and two 3.5" external drive bays.

Inside the case there are two 3.5" drive cages.

1.Pull the quick release lever towards the rear of the case and release the top cage first. Looking from the rear of the case you can see some metal grills over the exposed (external) drive bays. Carefully put a screwdriver through the metal grill and gently push the plastic drive bay cover until it comes off. Carefully use your hands to twist the metal plate back and forth until it breaks off.

Note: Don't take off the covers and plates for the drive bays that you are not using now. Be careful of the newly exposed metal where the grills were attached, as these areas are likely to be sharp.

2.Install your floppy drive into the top drive bay.

3.Mount your other 3.5" device into the drive cage.

Note: If you want to have a cooling fan in the drive cage, you should install the fan before installing the drives.

4.Slide and lock the drive cage back into the case.

5.Release the second cage.

Note: Inside the cage you will find a fan bracket. This is for one of the optional 80mm cooling fans. If you want to install the optional fan you should do it now. For fan installation please see the Fan Installation section of this manual.

6.Mount your other 3.5" devices into the drive cage.

7.Slide and lock the drive cage back into the case.

8.Find a small 4-pin white connector on the power supply and connect it to the male 4-pin connector on the floppy drive.

9.Connect a large 4-pin white connector from the power supply to the male 4-pin connector on each of the other devices.

5.25" Device Installation

1.Take off the plastic drive bay covers and metal plates as described above.

2.Take two of the Drive Rails and mount them to the sides of the 5.25" device. Make sure the metal portion is angled away from the device and facing forward.

3.Slide the device into the drive bay until you hear a click.

4.Mount the other devices accordingly. Connect a large 4-pin white connector from the power supply to the male 4-pin connector on each of the devices.

Data Cable Connection

After you have connected the devices to the power supply, you need to connect the data cables between the devices and the motherboard. The data cables are not included with the case; we include this information only as an aid.

1.For hard drives and CD-ROM's, use the 40-pin IDE ribbon cables. For floppy drives, use the 34-pin IDE ribbon cables. These should come with your motherboard and have a red strip on one side indicating pin number 1. When you connect a ribbon cable to a device, make sure that the red strip is on pin 1, usually toward the power connector.

2.The end that attachs to devices should be the side that has 2 connectors. This will enable you to connect another device if you wish.

3.Connect the far end of the cable to your motherboard on the IDE port, either IDE 1 or IDE 2, or the FLOPPY port.

Fan Installation

The case comes preinstalled with two 80mm cooling fans in the rear. The fans are installed so that the air is blowing out of the case. Connect a large 4-pin white connector from the power supply to the male 4-pin connector on each of the fans.

Optional Cooling fans: The case has two optional 80mm cooling fans that can be installed in the front of the case. One of the optional fans is located inside the 3.5" drive cage. You should install the fan first before you mount your drives into the cage. Install the fans so that the air is blowing into the case from the front.

1.Drop the fan into the fan bracket and push it in until it snaps in.

2.Connect a large 4-pin white connector from the power supply to the male 4-pin connector on each of the fans.

Washable Air Filter Maintainence

From time to time it will be necessary to wash the installed air filter. Not washing the air filter will result in higher system temperatures and possible stability problems. We recommend checking the air filter at least once a month initially. The frequency will change depending on system usage (users whose systems run 24/7 will likely have to check/wash more often than those who don't use their systems every day) and on environmental conditions.

SX1000II, SX1000BII specifications

The Antec SX1000BII and SX1000II are two remarkable additions to Antec's suite of computing solutions, designed to fulfill the demands of performance-oriented users and enthusiasts. These cases boast features that enhance compatibility, cooling, and aesthetics, establishing them as top choices for system builders looking to house powerful hardware in a sleek package.

One of the standout features of both models is their spaciousness. With a roomy interior that accommodates motherboards of all sizes, including ATX, micro-ATX, and mini-ITX, the SX1000BII and SX1000II offer ample space for high-performance GPUs and additional storage options. The cases can comfortably house graphics cards measuring up to 15.4 inches in length, making them compatible with most modern graphics solutions.

Cooling is a primary aspect of any gaming or performance setup, and both the SX1000BII and SX1000II excel in this area. They come equipped with multiple fan mounting options, supporting up to seven 120mm or 140mm fans for optimal airflow. Additionally, each case provides room for liquid cooling radiators, ensuring that even the most intensive gaming sessions or demanding tasks won’t lead to thermal throttling.

Another notable technology found in these models is the effective cable management system. Antec has designed these cases with dedicated routing cutouts and tie-down points, helping users maintain a clean and clutter-free interior. This feature not only enhances aesthetics but also promotes better airflow, as obstructions are minimized.

Both cases are constructed from steel and feature a mesh front panel, which improves airflow while giving them a modern trench-look design that appeals to gamers and professionals alike. The removable dust filters ensure that the interior remains clean, further enhancing the longevity of components.

For connectivity, the SX1000BII and SX1000II come with a convenient I/O panel that includes USB 3.0 ports and audio jacks, providing easy access to essential connections.

In summary, the Antec SX1000BII and SX1000II are superior cases that offer a blend of functionality, aesthetics, and effective cooling solutions. Whether for a high-speed gaming rig or a workstation, these models stand out due to their spacious designs, flexible cooling options, efficient cable management, and ease of access. Building a system with either case promises a blend of durability and style, ensuring user satisfaction in both performance and appearance.