Controls
Troubleshooting |
OSD Position Menu
POSITION
PRESSKEY
Color Adjust Controls Menu
COLOR - TEMP
OSD
USER 6500K 9300K
: Moves the OSD Position vertically up or down.
: Moves the OSD Position horizontally left or
right.
RB GB BB RG GG BG
USER | 50% |
Troubleshooting guide |
|
|
| ENGLISH | ||
If your monitor is not performing properly, please use the following troubleshooting chart for |
| |||||
quick solutions to common problems. |
|
|
| |||
|
|
|
|
|
| |
|
|
|
|
|
|
|
| Problem | Possible cause | Remedy |
|
| |
|
| |||||
|
|
|
|
|
|
|
|
| Is the power cord connected? | Connect power cord. |
|
|
|
|
|
|
|
|
|
|
|
| Is the power switch on? | Turn on power switch. |
|
| |
|
|
|
|
|
|
|
| No Picture | Is the signal cable properly | Connect signal cable properly |
|
|
|
|
| connected? |
|
|
|
|
|
|
|
|
|
|
|
|
| Is the monitor in the power save | Press any key on the keyboard or |
|
| |
|
| mode? | move the mouse. |
|
| |
EXIT : Exit to the main menu.
Controls 
: Increase or decrease the Selected color adjustment.
Controls | : Move the bar in the or direction to select the color setting |
| (USER, 6500K, 9300K). |
DO : Proceed to the selected Submenu choice (Press DO button for 5 seconds).
Presetting : Select the desired color setting. The bar is replaced by the color setting choice
“USER, 6500K or 9300K” Each color setting is adjusted at user mode to choose
|
| degree or Kelvin. |
| ||||||
|
|
|
|
|
|
|
|
| |
|
| Controls |
| ICON |
| Function | |||
|
|
|
|
|
|
|
|
|
|
|
| Information |
|
|
|
|
|
| This control shows the Factory and user mode |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| information. |
|
|
|
|
|
|
|
|
|
|
|
| Video Level |
|
|
|
|
|
| This control allows the video input level selection applied |
|
|
|
|
|
|
|
|
| by signal source. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This control allows the video input type selection. | |
|
|
|
|
|
|
|
|
|
|
|
| Degauss |
|
|
|
|
|
| This control removes the |
|
|
|
|
|
|
|
|
| can affect color purity and convergence. |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| Note : The picture shakes while degaussing is taking |
|
|
|
|
|
|
|
|
| place. After internal degaussing the circuitry takes about |
|
|
|
|
|
|
|
|
| 30 minutes to regain its maximum power. |
|
|
|
|
|
|
|
|
|
|
|
| Recall |
|
|
|
|
|
| This controls recalls certain factory setting such as size, |
|
|
|
|
|
|
|
|
| position, geometry and color by pressing DO button. |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| If the monitor is operation in a user mode, this controls |
|
|
|
|
|
|
|
|
| has no effect. |
|
| Zoom Menu |
|
|
|
|
|
| : Increase or decrease the Vertical and Horizontal size |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| of image at the same time. |
|
|
|
|
|
|
|
|
| |
12 |
| User’s Manual |
|
|
|
|
|
| |
|
| Is the signal cable properly | Connect signal cable properly |
|
| connected? |
|
|
|
|
|
| Picture is | Are there signals which are | Input signals which are within the |
| unstable | outside of the required frequency | range of the monitor. |
|
| range? |
|
|
|
|
|
|
| Is the signal connector pin | Use correct signal connector. |
|
| assigments correct? |
|
|
|
|
|
|
| Are there signals which are | Use correct signal which within the |
| The display | outside of the required frequency | frequency range of the monitor(If |
| image is not | range? | the signal is correct, adjust the |
| centered, too |
| controls to desired image.) |
| small or large. |
|
|
|
|
|
|
| The color of | Is the magnetic object nearby? | Move object far away. |
|
|
| |
image on screen | Is the pin arrangement of the | Use correct signal cable. | |
| is abnormal. | ||
| signal connector correct? | Use degauss control. | |
|
| ||
User’s Manual | 13 |