HANNspree M19N2, M19W2 Regulatory Information, FCC Class B Radio Frequency Interference Statement

Page 3

REGULATORY INFORMATION

Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference.

FCC Class B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CANADA

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation.

This device complies with requirement of EMC directive 89/336/EEC with regard to Electromagnetic Compatibility, and 73/23/EEC and 93/68/EEC with regard to Low Voltage directive.

Socket-outlet shall be near the equipment and shall be accessible.

2

Image 3
Contents Liquid Crystal Display Monitor Table of Contents FCC Class B Radio Frequency Interference Statement Regulatory InformationEmissions CongratulationsErgonomics EnergyRecycling Information Precautions Safety NoticeSpecial Notes on LCD Monitors Page Preface Features Checking the Contents of the PackageBefore YOU Operate the Monitor Power WarrantyDVI-D/HDMI Cable Cable Connections Controls and ConnectorsConnecting Cables Adjusting the Viewing Angle Operating Instructions General InstructionsExternal Controls Menu / Enter Front Panel ControlHOW to Adjust a Setting Phase adjustment Horizontal position adjustmentVertical position adjustment Clock adjustmentVideo mode Backlight ModeHow to adjust color Change Color Settings for D-SUB Change Color Settings for HdmiSource OSD vertical position adjustment How to set the OSDSelect OSD Setting from the Main OSD horizontal adjustmentOSD color setting OSD Transparency settingAdjust the transparency of the OSD Press Menu key and adjust the levelSharpness of the display. Set Volume adjustmentSelect the Sharpness option to adjust SharpnessInput Setting Near Timing ModeDOS mode Recall the factory settingsPlug and Play Plug & Play DDC2B Feature Trouble Shooting Technical Support FAQCable not Connected Error Message & Possible SolutionKHz Factory Preset Timing TableFREQ.Hz Hdmi Timing TableAppendix SpecificationsUL/CUL, BSMI, CCC, CE, CB, PSB, FCC Pin Color Display Signal Cable Connector PIN AssignmentPin Color Display Signal Cable Dual Input Mode ファックス

M19W2, M19N2 specifications

The HANNspree M19N2 and M19W2 are two notable models in the realm of computer monitors, designed to cater to a variety of needs ranging from everyday computing to entertainment. Both models embody the brand's commitment to delivering quality and performance at an accessible price point.

The HANNspree M19N2 is a 19-inch monitor that makes a strong impression with its sleek design and impressive display capabilities. It features a resolution of 1366 x 768 pixels, allowing for vivid colors and sharp images. The display utilizes an advanced LED backlight technology, enhancing brightness and contrast while consuming less power than traditional LCDs. This makes it not only environmentally friendly but also cost-effective in terms of energy consumption.

On the other hand, the HANNspree M19W2 also boasts a 19-inch display but comes with a higher resolution of 1440 x 900 pixels, which provides a slightly elevated pixel density. This increase in resolution contributes to a more detailed and clearer visual experience, making it ideal for tasks like graphic design, video editing, or even casual gaming. Both monitors feature a wide viewing angle, typically around 170 degrees, which ensures that colors remain consistent and true to life even when viewed from off-angles.

One of the main characteristics of these models is their connectivity options. The M19N2 and M19W2 come equipped with multiple input ports, including VGA and HDMI, making it easy to connect to a variety of devices like laptops, desktops, or gaming consoles. Furthermore, they are compatible with both Windows and macOS operating systems, providing versatility to different user preferences.

Both monitors are ergonomically designed. They offer tilt functionality, allowing users to adjust the viewing angle for maximum comfort. This feature is particularly beneficial for those who spend long hours in front of the screen, helping to reduce neck strain. In terms of aesthetics, the contemporary design and slim bezels of the M19N2 and M19W2 make them an attractive addition to any workspace or home setup.

In summary, the HANNspree M19N2 and M19W2 are excellent choices for users seeking reliable performance and solid features in a compact monitor. With their impressive resolutions, advanced technologies, and user-friendly designs, they stand out as commendable options in the entry-level monitor segment. Whether for professional tasks or leisure activities, these models deliver quality that resonates well with a broad audience.