Behringer V-TONEGM110 manual Rear panel, Behringer V-TONE Model GM110

Page 6

V-TONE GM110

With the MASTER control, you determine the overall and headphone volume of your V-TONE GM110. It should be set fully to the left when you operate the POWER switch or disconnect the instrument cable from the guitar or amp.

Use the POWER switch to put the GM110 into operation.

The POWER switch should always be in the “Off” position when you are about to connect your unit to the mains.

+Attention: The POWER switch does not fully disconnect the unit from the mains. Unplug the power cord completely when the unit is not used for prolonged periods of time.

2.2 Rear panel

BEHRINGER® V–TONE

 

MODEL GM110

 

CONCEIVED AND DESIGNED

 

BY BEHRINGER GERMANY.

 

ASSEMBLED IN CHINA UNDER

 

ISO9000 CERTIFIED

 

MANAGEMENT SYSTEM.

 

CAUTION

 

REPLACE WITH SAME FUSE

 

TYPE AND RATING.

 

ATTENTION

 

UTILISER UN FUSIBLE DE

 

RECHANGE DE MEME

 

TYPE ET CALIBRE.

OUTPUT

230 V

: 50/60 Hz 70 W

 

FUSE:

˜T 1.0 A H 250 V

 

Fig. 2.2: Rear panel connectors

FUSEHOLDER / VOLTAGE SELECTION. Before you

 

 

At the D.I. OUT output (balanced XLR socket), you can tap

 

 

connect the device to the network, please make sure that

 

 

the audio signal of the V-TONE GM110 in order, for example,

your local voltage matches the voltage indicated on the

 

 

to feed it into a mixing console and record it. This audio

unit. Blown fuses may only be replaced by fuses of the

 

 

signal is frequency-corrected (Speaker Simulation). The

same type and rating. Some models allow for inserting the

 

 

level of the D.I. OUT (max. +22 dBu) is designed to provide

fuse holder in two different positions in order to switch

 

 

simple connection to mixers or other audio devices.

over from 230 V to 120 V operation, and vice versa. Please

 

 

With the GND LIFT switch, you can unplug the electrical

note that, for 120 V operation outside Europe, you need to

 

 

 

 

bonding of the D.I. OUT, if ground loop or humming problems

use a fuse of a higher rating. The network connection is

 

 

 

 

occur.

made via a STANDARD IEC INLET SOCKET. Use the

 

 

 

 

 

enclosed power cord to connect the unit to the mains.

 

 

FX SEND is the output socket for the serial effects path of

 

 

SERIAL NUMBER. Please take the time to fill out the

 

 

the GM110. You can use this to loop in the external effects

 

 

(e.g. a wah-wah pedal) or to connect an external power

warranty card within 14 days of purchasing the device,

 

 

 

 

amplifier, should you require a greater output. The internal

otherwise you will lose your extended warranty. Or simply

 

 

 

 

signal path will not be interrupted. The frequency-corrected

register online at www.behringer.com.

 

 

 

 

signal at the FX SEND socket is affected by all GM110

 

 

 

You can use the SPEAKER socket to connect an additional

 

 

controls.

loudspeaker to your V-TONE GM110. The external

 

 

The output of the looped-in effects device is connected to

loudspeaker should have an impedance of 4 Ohms. When

 

 

 

 

the FX RETURN socket. When you connect a cable to this

using this socket, the internal loudspeaker is muted. For

 

 

 

 

socket, you interrupt the internal signal path.

additional information on connecting an external

 

 

+ Please note that, when using the serial effects path,

loudspeaker, refer to chapter 4.1.

The 6.3 mm PHONES jack allows you to monitor the GM110’s

 

 

the effects device will control the level of wet

 

 

(affected) signal to dry (direct) signal.

audio signal with a pair of commercially available

 

 

 

 

 

headphones. As soon as this socket is used, the

 

 

 

loudspeaker will be muted.

 

 

 

+Since speakers can have quite an impact on the sound of a guitar amp, both the headphones and D.I. OUT signals are frequency-corrected (with speaker correction). Without this frequency correction extreme treble frequencies would deteriorate the sound.

+Low-impedance headphones may begin to produce distortion at certain volume levels. In such cases, please reduce the volume by turning back the MASTER control.

6

2. CONTROL ELEMENTS

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Tone Version 1.2 JulyImportant Safety Precautions Detailed Safety InstructionsRugged construction for years of trouble-free use Conceived and designed by Behringer GermanyDesign concept ForewordIntroduction Dynamizer technology and analog modelingControl Elements Before you get startedFront panel Rear panel Behringer V-TONE Model GM110Wiring Tips Audio ConnectionsSpecifications Loudspeaker connectionWarranty

V-TONEGM110 specifications

Introducing the Behringer V-TONE GM110, an electric guitar amplifier that combines powerful sound design with intuitive controls to accommodate both aspiring musicians and seasoned players. This compact yet feature-rich amp is built to deliver a wide array of tones, making it a versatile choice for any guitarist.

One of the standout features of the V-TONE GM110 is its unique modeling technology. This amplifier utilizes advanced DSP (Digital Signal Processing) to emulate a variety of classic amp sounds, allowing users to experiment with different tonal characteristics. Whether you are seeking the warm tube tones of vintage amplifiers or the aggressive sound of modern high-gain models, the GM110 has a setting to match your preferences. The flexibility of its modeling capabilities makes it equally effective for practice sessions as well as live performances.

The amp is equipped with a single 10-inch speaker that delivers impressive sound quality, ensuring that your playing is heard with clarity and depth. Additionally, the built-in digital effects processor adds further dimension to your sound. Guitarists can apply reverb, delay, and modulation effects, enriching their playing experience without the need for external pedals. This integrated approach facilitates easy adjustments, enabling players to create their perfect sound quickly.

User-friendliness is key in the design of the V-TONE GM110. The front panel features straightforward knobs and switches, allowing musicians to dial in their desired tone with ease. Controls for gain, treble, middle, and bass make it simple to shape the amp's overall sound, while the dedicated gain control allows players to push their tone into overdrive for solos or crunchy rhythms. Furthermore, the amp includes an aux input for jamming along to tracks, as well as a headphone output for silent practice.

Durability is also a critical aspect of the GM110, with a sturdy cabinet that can withstand the rigors of regular transport. Combined with its lightweight design, this amp is an ideal companion for musicians on the go.

In summary, the Behringer V-TONE GM110 stands out as a compact guitar amplifier that offers impressive versatility and tonal possibilities. Its modeling technology, built-in effects, and user-friendly interface make it suitable for players of all levels. Whether practicing at home or performing on stage, the GM110 is designed to enhance your musical expression and creativity. The blend of quality craftsmanship and innovative technology solidifies its place as a noteworthy option in the world of electric guitar amplifiers.
Top Page Image Contents